Interesting evening at the track...
Interesting evening at the track...
Went to South Georgia Motorsports Park for their T-n-T last Friday night. Only got in three runs, but they were all interesting to say the least.
First run:
Me vs. a 2002 Z28, auto. I won on a hole shot.
Me: 14.179 with a 2.179 60'
Him: 14.154 with a 2.196 60'
Something didn't seem right with that car.
Second run:
Me vs. a 1996 WS6, 6MT. Newbie driver.
Me: 14.070 with a 2.093 60'
Him: 14.632 with a 2.321 60'
Third run:
Me vs. a ~2001 Saleen S-281 with blower. Had the worst run of the night because the track was going away, but again, I won on a hole shot.
Me: 14.192 with a 2.220 60'
Him: 13.779 with a 2.131 60'
All of this in my wife's 2001 Pontiac GTP.
Been jonesin' to take somethin' to the track since my TA is under the knife at the moment and ended up being quite content. Not too bad for $120 in mods and +90* temps.
Marty
First run:
Me vs. a 2002 Z28, auto. I won on a hole shot.
Me: 14.179 with a 2.179 60'
Him: 14.154 with a 2.196 60'
Something didn't seem right with that car.
Second run:
Me vs. a 1996 WS6, 6MT. Newbie driver.
Me: 14.070 with a 2.093 60'
Him: 14.632 with a 2.321 60'
Third run:
Me vs. a ~2001 Saleen S-281 with blower. Had the worst run of the night because the track was going away, but again, I won on a hole shot.
Me: 14.192 with a 2.220 60'
Him: 13.779 with a 2.131 60'
All of this in my wife's 2001 Pontiac GTP.
Been jonesin' to take somethin' to the track since my TA is under the knife at the moment and ended up being quite content. Not too bad for $120 in mods and +90* temps.
Marty
Re: Interesting evening at the track...
Originally Posted by Steve Y
What $120 in mods do you have done? Impressive times!
Mods are:
$60 for a 3.4" pulley
$40 for a 9" K&N cone
$10 for the ABS septic piping pieces I used to fab up a home made CAI kit
$10 for a 160* thermostat
Thats it!
Marty
Re: Interesting evening at the track...
Originally Posted by 97ChameleonTA
Thanks! I'm quite surprised at how well it does too.
Mods are:
$60 for a 3.4" pulley
$40 for a 9" K&N cone
$10 for the ABS septic piping pieces I used to fab up a home made CAI kit
$10 for a 160* thermostat
Thats it!
Marty
Mods are:
$60 for a 3.4" pulley
$40 for a 9" K&N cone
$10 for the ABS septic piping pieces I used to fab up a home made CAI kit
$10 for a 160* thermostat
Thats it!
Marty
Re: Interesting evening at the track...
Those 3.8's are great engines. I almost never see them with serious problems, even the SC'd ones.
Was that pulley a lot smaller than stock? Or was it just a little smaller?
I bet with an exhaust system and maybe a computer tune that GTP would really run.
TONY
What kind of mph were you getting?
Was that pulley a lot smaller than stock? Or was it just a little smaller?
I bet with an exhaust system and maybe a computer tune that GTP would really run.
TONY
What kind of mph were you getting?
Re: Interesting evening at the track...
Yeah, I really can't complain about the car at all. So far it has been problem free and it takes to mods really well.
Stock pulley is a 3.8", the 3.4" is pretty much the first step smaller.
My MPH was averaging in the high 98's for the three runs (99.03, 98.82 & 98.87)
Marty
Stock pulley is a 3.8", the 3.4" is pretty much the first step smaller.
My MPH was averaging in the high 98's for the three runs (99.03, 98.82 & 98.87)
Marty
Thread
Thread Starter
Forum
Replies
Last Post
redzed
Automotive News / Industry / Future Vehicle Discussion
12
Aug 29, 2002 02:22 PM
Ude-lose
Automotive News / Industry / Future Vehicle Discussion
34
Aug 1, 2002 07:21 AM



