Parts Sold!

MPT70
Intercooler
Cam
Rods
Regulator
Sureflo oil pump
Holset Turbo
Silicone coupler




Plenty more to come!

I prefer paypal, none of these prices include shipping. If we decide on a shipping price and it ends up being less than the price stated, then I'll send you your extra money back with the purchased item. I do not make money on shipping.

Thanks

David Moss

 

Set of Pro Top Line heads for Small block chevy, 2.02 intake 1.60 valves, 3 angle valve job, high performance springs set up for .550 lift, 76cc chambers. $700

350 Chevy Block, 4 bolt main, 1 piece rear main seal, bored .060 over, $200


GM Forged Steel Crankshaft, 1 piece rear main seal, turned .010 on rods and mains. The transmission pushed forward on the crank and it contacted the main thrust bearing, so it needs to be checked out by machine shop, a little bit of bluing on main journal, the bearing did not spin. $75

1.5 full fulcum aluminum roller rockers, summit brand, used for about 50 miles. $120

Hardened crane push rods, stock 95 and up SBC push rod length, used for about 50 miles. $40


Edlebrock torquer 2 intake manifold, single plane design, it has 3 vacume fittings tapped into it under the carb for vacume readings and signals, $70

Flowtech Shorty headers for a 1993 Chevy C1500 pickup V-8 5.7, has 2.5" v-band flange welded on the end of collectors, $125 (paid $230 for from advance)

Chevy HEI distributor with spring kit included, vacume advance and mechanical advance works, new rotor and cap, Cap has ACCEL high output coil included. The distributor doesn't have a module in it cause it was used with a MSD box, but a module can be reinstalled by buyer. $50

CSU Carb Hat, it has 3" aluminum tubing welded onto the end of it, I didn't have to use a 3.5 to 3" silicone reducer, just a plain 3" silicone coupler, $90

MSD 6AL BTM, brand new, absolutely perfect, used for about 10miles, I paid $400 for, want $325.

(6) 3" t-bolt clamps, BRAND NEW NEVER USED, ordered about 3 weeks ago, paid $6 each for, will take $25 for all.

(4) pieces of 3" silicone hose, each about 3 to 4" in length, $15 for all

I can get pics of parts, just call me tommorow and let me know what pics you want, or send an e-mail at dmoss69@yahoo.com.

More to come:
David (803)682-5099

 

pics are posted at:

http://s25.photobucket.com/albums/c56/dmoss69/

Thanks

D Moss

 

The wastegate is a 40mm that i purchased off of a member of camaroz28.com, I have 2 springs to go with it, one is supposed to be a 6 psi, and the other is supposed to be 14, but the 14psi spring is not right, it'll go over 14psi. The spring in the wastegate is a 10 for sure, I've seen it work correctly. $200

I have pictures of the exhaust that I had on the truck, it is 4" all the way back to the "y", so I'll cut off all the 90* and 45* mandrel bends out of it and sell them for $15 each.

The large 16" muffler is a dynomax 4" race magnum muffler, straight through design, I'll sell it for $60.

The other mufflers are dynomax 3" ultraflows, center inlet offset outlet, straight through design, $55 each.

The one piece rear main seal oil pan with 3/4 drain fitting welded into the pan, $50

Yellow timing chain cover, $15

The "s" intake tubbing made out of "u" mandrel style bends 3", $30 (silicone coupler comes off)


The pic of the thin metal coupler, I used these on my removeable "s" pipe that I had so I could drop the transmission if I needed to. They are 4", and they worked great. $10 each. I have 2 of these.

I can mail these out Friday since I"m working night shift this week, I may be able to get them out sooner, so bear with me. The parts are at my shop, which is 20 min away. I'll try to be as speedy as can be, and I'll also try to keep EVERYONE up to date with sales.

Just e-mail me at dmoss69@yahoo.com, or PM me.

Thanks

David Moss

 

is everything sold?

 

TURBO AND INTERCOOLER ARE ON THE WAY!!!!!

Not all of the parts are sold, only the parts listed at the top of the thread, everything else is still avaliable!

D Moss