Forged 383LT1 shortblock for sale
Thread Starter
Registered User
Joined: Feb 2002
Posts: 5,645
From: Bridgewater, MA
Forged 383LT1 shortblock for sale
I am looking to sell this as a package. The components were assembled and run for 5k miles before I got them by Aggiez28. All parts checked out fine by his machine shop. The short block is disassembled:
4 bolt block completely machined (Aligned honed, notched, 4 bolt splayed conversion) etc. The cylinder bores have a little surface rust, it just needs a a quick ball hone to clean it up. i assume you would want that anyway so the cross hatching could be put in for the new piston rings.
Cola 3.75" forged Crank (1pc rear main seal). this crank is rated as one of the best cranks out there.
Eagle H Beam 5.7" forged rods with ARP bolts
SRP -31cc Forged Pistons
Oliver Billet 4 bolt splayed main caps
ARP rod bolts and studs
The assembly is set up for a zero balanced flywheel. I will also throw in my Bret Bauer custom blower cam for an extra $250 (this cam is new, billet, and will make more power than most off the shelf blower cams). Specs are similar to a cc306, but more blower friendly. According to Bret Bauer this cam with ported stock castings, 383, and S trim @ 14.5psi should make ~680hp/700tq at the flywheel.
I am asking for:
$2200 shipped freight (thats gonna cost me ~200) for the engine components
$2450 for engine components with the cam
All you need is new bearings and rings and your all set. Just the machine work alone would cost 1000-1200 and the rotating assy is an easy $2k for a total over $3k. This is a great deal for someone who wants to build their own power adder motor.
Please email me for questions/concerns: jrbellas95z28@yahoo.com
4 bolt block completely machined (Aligned honed, notched, 4 bolt splayed conversion) etc. The cylinder bores have a little surface rust, it just needs a a quick ball hone to clean it up. i assume you would want that anyway so the cross hatching could be put in for the new piston rings.
Cola 3.75" forged Crank (1pc rear main seal). this crank is rated as one of the best cranks out there.
Eagle H Beam 5.7" forged rods with ARP bolts
SRP -31cc Forged Pistons
Oliver Billet 4 bolt splayed main caps
ARP rod bolts and studs
The assembly is set up for a zero balanced flywheel. I will also throw in my Bret Bauer custom blower cam for an extra $250 (this cam is new, billet, and will make more power than most off the shelf blower cams). Specs are similar to a cc306, but more blower friendly. According to Bret Bauer this cam with ported stock castings, 383, and S trim @ 14.5psi should make ~680hp/700tq at the flywheel.
I am asking for:
$2200 shipped freight (thats gonna cost me ~200) for the engine components
$2450 for engine components with the cam
All you need is new bearings and rings and your all set. Just the machine work alone would cost 1000-1200 and the rotating assy is an easy $2k for a total over $3k. This is a great deal for someone who wants to build their own power adder motor.
Please email me for questions/concerns: jrbellas95z28@yahoo.com
Last edited by RealQuick; Feb 2, 2005 at 12:28 PM.
Thread Starter
Registered User
Joined: Feb 2002
Posts: 5,645
From: Bridgewater, MA
Re: Forged 383LT1 shortblock for sale
Originally Posted by 95LT1Z28
Do you have any pics of the block and rest of the rotating assembly?
Jeff
Jeff
Thread
Thread Starter
Forum
Replies
Last Post