RHS 235 heads and Super Vic IN THE CAR BABY!
#1
RHS 235 heads and Super Vic IN THE CAR BABY!
Well It's in the car! Along with the transmission and driveshaft. Still lots to do but I knocked down a big hurdle today! ECM left for Ed Wright on Friday for the break in tune.... the hood closes with no mods(Suncoast ram air hood)
[/IMG]
[/IMG]
David
[/IMG]
[/IMG]
David
Last edited by FASTFATBOY; 04-28-2007 at 08:54 PM.
#4
Those are flange plate adaptors that allow the use of race headers. Since they permit a wider bolt pattern for the header flange, the pipes aren't restricted by the stock pattern. There's a clearer picture of them in Jeg's Catalog in the header section. The use of flange plate adaptors is widespread in racing applications.
#5
looks good, What headers you going with? someone I know had his made with stahl flanges and they were $2200....just wondering what your going with and um....with all that stuff why the a/c and power stearing?
I would have tossed that stuff....its just alot of clutter
I would have tossed that stuff....its just alot of clutter
#7
Headers are a 1 7/8 Hedman's Modified to work with A/C and power steering. Along with a 3.5 inch Y pipe and a 4 inch Mufflex.
Hey it's a street car! Gotta have A/C
95TTop, $1100...was for a COMPLETE set of headers? Coated and Ready to bolt on the car?
The elbow is from intakeelbows.com.
David
Hey it's a street car! Gotta have A/C
95TTop, $1100...was for a COMPLETE set of headers? Coated and Ready to bolt on the car?
The elbow is from intakeelbows.com.
David
Last edited by FASTFATBOY; 04-29-2007 at 06:39 AM.
#8
$1100 was uncoated and ready to bolt on, stepped with a 4in collector I think. Spread flange and slip on collectors.
I'm not sure who much getting a set coated is? 2-400 maybe??
What are you doing for PCV? I see two breathers, is there a vaccum pump in the works?
I'm not sure who much getting a set coated is? 2-400 maybe??
What are you doing for PCV? I see two breathers, is there a vaccum pump in the works?
#9
My Jet Hot MC-15 coating was $400, but I didn't pay shipping, they are 20 minutes from here, I just dropped them off.
I have talked to many people on the pcv deal. I am gonna run baffled breathers and see how it does. I was gonna run a pcv with an oil seperator...but am gonna try this first. Vacuum pumps only really work with a totally sealed engine...really work best on race applications.
With my setup I don't want ANY oil in the intake tract, not even a film. I am at the limits on pumpgas.
I have talked to Thunder Racing's guys about the PCV vs vents deal...I have a good friend with a 408 inch LS2 in a car he is daily driving(it's a NASTY combination)...it also has no pcv, just a vented catch can. Thunder built this car and I am watching how it does. Gotta think pcv only really came out with the advent of emissions...did the older cars even have it? I am talking mid 60's.
DO a search on here for Turbo6, he also has a NASTY 485 rwhp Lt1 with vents, no pcv.
David
Last edited by FASTFATBOY; 04-29-2007 at 07:19 AM.
#11
Thanks man, been a LONG time coming......can't wait to bust it off..but it is gonna be a little while yet....got to move some stuff around in the wiring harness, find a place to mount the MAP sensor, figure out a throttle cable,,the list of little stuff is LONG.....but I just scratch them off as I go.
David