SPEC Stg 3 Clutch & Misc LT1 Parts
#1
SPEC Stg 3 Clutch & Misc LT1 Parts
A few items I want to get rid of and others I bought but don't have time to install because of school:
Spec Stage 3 Clutch- New, in box, never used or installed, - $400 shipped SOLD
"Salad Shooter" Rims w/ caps- Usable condition, was going to polish them, have one rim down mostly to bare metal, but it's just too much work for me- will need to be painted if you want them to look nice- $80 obo
Exhaust Manifolds- one stud broken on removal, will need to be replaced- $30 obo
Y-pipe w/ working cat- $30 obo
Cat- back exhaust- Factory I-pipe w/ Dynomax rear section- good condition, would recommend welding for no leaks, was cut in two places on removal but they were clean cuts in the same places an aftermarket unit has them for installation- $20 obo
EGR- works as far as I know (never set codes) - $10 obo
LS1 Injectors- bought them for my LT1 for a heads & cam swap that never materialized, tried them out anyway, they work fine, they'll leak on an LT1 unless you buy special clips for them or else cut the groove on the opposite side- basically they have grooves for the LT1 clips but they're 90 degrees off so the wiring hookup sticks up at the fuel rail instead of out to the side. They are the later 28 lbers. pt # 12561462.- $50 obo
1LE Swaybar- new & never installed, 32 mm- $30 obo
3.23 gearset- out of my car for 4.11s, teeth appear to be in good condition, no chips, comes w/ bolts if you want them- the end of the pinion where the nut threads on got a little misshapen- my fault for not using a brass punch- shouldn't affect operation, however, I did the same thing to the 4.11s I installed trying to get the proper pattern. I can grind a little on the edges so the nut will thread on if you like. You'll still need an install kit to be safe though, I only have one of the pinion bearings on there, takes a .035 shim btw.- $20 obo
Driveshaft- stock, rust has been sanded off, some surface rust from sitting outside. Needs a new u-joint, caps fell off on one end.- $20 obo
Please e-mail me at craigkzoo@yahoo.com if you have any questions or want pictures, I would be more than happy to take as many pictures as you would like if it would help you make a decision. Shipping is only included on the clutch, as some of these items are rather large and it would probably double their price, so I would rather do pickup if possible, I would be willing to meet maybe an hour or so away from home for the cost of gas. All parts are in Kalamazoo, Michigan. I'm on break in between schools right now, so please be patient. If they don't sell you'll probably see them on ebay later.
Spec Stage 3 Clutch- New, in box, never used or installed, - $400 shipped SOLD
"Salad Shooter" Rims w/ caps- Usable condition, was going to polish them, have one rim down mostly to bare metal, but it's just too much work for me- will need to be painted if you want them to look nice- $80 obo
Exhaust Manifolds- one stud broken on removal, will need to be replaced- $30 obo
Y-pipe w/ working cat- $30 obo
Cat- back exhaust- Factory I-pipe w/ Dynomax rear section- good condition, would recommend welding for no leaks, was cut in two places on removal but they were clean cuts in the same places an aftermarket unit has them for installation- $20 obo
EGR- works as far as I know (never set codes) - $10 obo
LS1 Injectors- bought them for my LT1 for a heads & cam swap that never materialized, tried them out anyway, they work fine, they'll leak on an LT1 unless you buy special clips for them or else cut the groove on the opposite side- basically they have grooves for the LT1 clips but they're 90 degrees off so the wiring hookup sticks up at the fuel rail instead of out to the side. They are the later 28 lbers. pt # 12561462.- $50 obo
1LE Swaybar- new & never installed, 32 mm- $30 obo
3.23 gearset- out of my car for 4.11s, teeth appear to be in good condition, no chips, comes w/ bolts if you want them- the end of the pinion where the nut threads on got a little misshapen- my fault for not using a brass punch- shouldn't affect operation, however, I did the same thing to the 4.11s I installed trying to get the proper pattern. I can grind a little on the edges so the nut will thread on if you like. You'll still need an install kit to be safe though, I only have one of the pinion bearings on there, takes a .035 shim btw.- $20 obo
Driveshaft- stock, rust has been sanded off, some surface rust from sitting outside. Needs a new u-joint, caps fell off on one end.- $20 obo
Please e-mail me at craigkzoo@yahoo.com if you have any questions or want pictures, I would be more than happy to take as many pictures as you would like if it would help you make a decision. Shipping is only included on the clutch, as some of these items are rather large and it would probably double their price, so I would rather do pickup if possible, I would be willing to meet maybe an hour or so away from home for the cost of gas. All parts are in Kalamazoo, Michigan. I'm on break in between schools right now, so please be patient. If they don't sell you'll probably see them on ebay later.
Last edited by GreenDemon; 11-11-2005 at 04:53 PM.
#2
Re: SPEC Stg 3 Clutch & Misc LT1 Parts
Is that clutch for LT1 setup or LS1? If its an LT1 clutch please send pics to ssher1@socal.rr.com
Thanks
Steve
Thanks
Steve
#4
Re: SPEC Stg 3 Clutch & Misc LT1 Parts
Originally Posted by blackz97
Is that clutch for LT1 setup or LS1? If its an LT1 clutch please send pics to ssher1@socal.rr.com
Thanks
Steve
Thanks
Steve
#13
Re: SPEC Stg 3 Clutch & Misc LT1 Parts
Hey GreenDemon!
Do you have pics of the LT1 exhaust?
What size is it?
How much is shipping?
is it aluminum?
what does "dynomax rear section" mean?
What year is that?
thanks!
jlb00h@hotmail.com
Do you have pics of the LT1 exhaust?
What size is it?
How much is shipping?
is it aluminum?
what does "dynomax rear section" mean?
What year is that?
thanks!
jlb00h@hotmail.com
Last edited by jonathan_abilene; 12-13-2005 at 06:01 AM.
Thread
Thread Starter
Forum
Replies
Last Post
High HP TA
Car Audio and Electronics
0
09-06-2002 08:00 PM