Unless otherwise listed all parts work with 93-97 LT1 F-bodies and PLUS Shipping. Paypal accepted and preferred.

STOCK

Alternator - $25
Starter - $25
Power steering pump w/ pulley - $25
Accessory bracket (for ps pump, ac, alt), powder coated gray - $40
Upper radiator support/shroud - $20
Fuel Pump/sender - $50
O2 sensors - $35 per pair
MAF stock with screen - $40
MAF Ported with no screen or center bar - $50
A4 & M6 Radiator - $50
Fans - $60
A4 transmission crossmember - $20
M6 Transmission crossmember - $45
Flexplate - $20
OBDI and OBDI pcms (will need programmed to your specific car) - $65
EBCM/ABS module/block - $25
Windshield wiper arms, $20 per side, $30 for both
Good working condition ac delco opti with 10k on it (95-97) - SOLD
Good working ac delco opti with 15k on it for 92-94 - $125
Vented opti electric and vaccum harness - $25 for the pair
Pair of 97-02 Tail lights - $30 each or $50 for both
Automatic Shifter assembly - $30
Automatic pedals - $30
Side mirror in black, sebring silver - $25 each side or $40 for both
Stock harmonic balancer pulley - $20
Black Berger panel - $85
Stock valvecovers - $15
Stock Oil Pan - $25
Stock valvecovers powdercoated red - SOLD
Rear main seal retainer, aluminum stock piece - $25



AFTERMARKET/PERFORMANCE


Morel Linkbar hydraulic roller lifters, very low mileage - $300
Dynaspark Optispark for 92-94, converts your Gen I opti into vented without needing to convert anything else (was new on Nov 10, used during summer of '11 for 8k) - $375
Dynaspark - The last distributor you'll ever have to buy
JEGS SFI balancer and hub - SOLD
Aluminum Polished Valve covers with notch for alternator - SOLD
ATI neutral balance flexplate - SOLD
Granatelli MAF - $125
March Underdrive pulley for crank pulley, with bolts & belt- $45
Maximum ported LT4 Intake manifold, pm for more details, no longer powder coated - $375
MSD Coil 92-95 - $25
Taylor OTVC wires black without mounts - $60
Ebay CAI - SOLD
Madman altenator relocation bracket - SOLD
LT4 ED timing chain set - SOLD
Moroso 7 quart pan, black (similar to canton design without trap doors), specifically made for LT1 F-bodies. Comes with pickup needed - $200
Canton 242t oil pan, modified and sort of cobbled for fitment on a turbo car, will need repaired/rewelded, email for pics - $50
Pairs of poly endlinks (front or rear) - $15

 

Bump it up! UMI torque arm is sold! Spintech exhaust sold!

 

got a pic of those polished Alum valve covers? Brand?

 

Here are some pictures of the v/cs. I don't really know the brand on them as it isn't stamped or cast into them anywhere. Only thing thats cast into them is SSI on the underside which doesn't mean anything to me??

 

hey doug send me a pic of the morels?

 

Here are some Morel pics for ya also sent em to your inbox....

 

What condition is the MAF sensor in?

 

i need an obd1 pcm pm me plz or email at almarji13@gmail.com
thanks

 

^^^ Sent you a pm on the pcm.

All them MAFs I have for sale are in excellent working condition. Im not sure which you were asking about since i have a few....

 

Polished valve covers, 1 LT4 ED timing set, powder coated valve covers, ALL SOLD!

 

How much for the driveshaft shipped to 31601?

 

How is the paint on the Berger pannel ? I"m kinda picky.

 

Sent a pm on the driveshaft


I would say if you are picky its probably not the one for you.

 

Thanks anyway..I'd rather you be honest than me be unhappy.

 

Pics of the canton oil pan please? I have a welder so I can make repairs, and will it fit on a lt1 crossmember?

does the madman relocation include the belt?