GTP Stage IV heads/SR setup, TH400 + 'vertor & shortblock.
Thread Starter
Registered User
Joined: Sep 1998
Posts: 137
From: Horsham, PA
GTP Stage IV heads/SR setup, TH400 + 'vertor & shortblock.
I am parting out my combo and going a different route. Below is what I have to sell. The motor is a 11.7:1, 6.0" H-beam, SCAT 9000 series, SRP forged piston 383 solid roller. The top end was bought from INTMD8 2 years ago and I have put less than 800 miles on this combo. Below is a link to his dyno run with these exact parts (453rwhp / 416rwtq). I also have a copy of the dyno tune for this combo. I am not interested in parting out the shortblock, that stays together. Everything listed below together should be good for a 10 sec NA ride.
Here we go:
Top End:
* Stage IV GTP heads, ported LT1 intake, custom grind cam motion 250 duration / .600 lift solid roller cam.
* GTP states they flowed 297cfm @.600 on the intake with a 2.055 valve and a 197cc intake runner, but the dyno graph speaks for itself: http://www.afrashteh.com/intmd8-dyno-383.jpg.
* Also going with these heads/intake as a combo are the chromoly pushrods and solid roller lifters.
* The heads were just done over by a local machine shop and are totally redone and ready to go (have receipt).
Asking $2600 for everything under "Top End"
***Price reduced, $2200****
Shortblock:
* LT1 2 bolt main, fully machined stroker block.
* 6.0" Scat Pro series H-beam rods with ARP rod bolts.
* SRP forged flat top pistons (11.7:1 with above heads)
* SCAT 9000 series stroker crank.
* @800 miles on this shortblock.
$1500
TH400 Tranny:
* Brand new, still on the crate COAN Engineering TH400 Competition Trans part number 21110-0 and COAN Engineering 10inch Competition Convertor Part Number: 20316 (brand new in the box) for sale.
$1300 OBO for both.
***Price reduced, $1100***
I also have miscellaneous stuff for sale, everything listed was on the car for @800 miles.
* Fluidampr crankshaft balancer.
* BBK 58mm TB
* CSI electric water pump
* 95+ Vented Opti conversion
* 1.6 Roller rockers (can't remember the make, will double check and update the post)
* LT4 valve covers
* SVO 36# injectors.
I think that's about it . . . I'll go for best offer on the miscellaneous stuff. Serious inquiries only please.
Everything is out of the car and ready to go. Any questions feel free to email me (WildThing94Z@hotmail.com) or post here.
Thanks,
Pete
(don't know why the post count is so low and Junior member is there. I had @ 750 posts since the last time. I'm not a newbie and have been on this board for a while)
Here we go:
Top End:
* Stage IV GTP heads, ported LT1 intake, custom grind cam motion 250 duration / .600 lift solid roller cam.
* GTP states they flowed 297cfm @.600 on the intake with a 2.055 valve and a 197cc intake runner, but the dyno graph speaks for itself: http://www.afrashteh.com/intmd8-dyno-383.jpg.
* Also going with these heads/intake as a combo are the chromoly pushrods and solid roller lifters.
* The heads were just done over by a local machine shop and are totally redone and ready to go (have receipt).
Asking $2600 for everything under "Top End"
***Price reduced, $2200****
Shortblock:
* LT1 2 bolt main, fully machined stroker block.
* 6.0" Scat Pro series H-beam rods with ARP rod bolts.
* SRP forged flat top pistons (11.7:1 with above heads)
* SCAT 9000 series stroker crank.
* @800 miles on this shortblock.
$1500
TH400 Tranny:
* Brand new, still on the crate COAN Engineering TH400 Competition Trans part number 21110-0 and COAN Engineering 10inch Competition Convertor Part Number: 20316 (brand new in the box) for sale.
$1300 OBO for both.
***Price reduced, $1100***
I also have miscellaneous stuff for sale, everything listed was on the car for @800 miles.
* Fluidampr crankshaft balancer.
* BBK 58mm TB
* CSI electric water pump
* 95+ Vented Opti conversion
* 1.6 Roller rockers (can't remember the make, will double check and update the post)
* LT4 valve covers
* SVO 36# injectors.
I think that's about it . . . I'll go for best offer on the miscellaneous stuff. Serious inquiries only please.
Everything is out of the car and ready to go. Any questions feel free to email me (WildThing94Z@hotmail.com) or post here.
Thanks,
Pete
(don't know why the post count is so low and Junior member is there. I had @ 750 posts since the last time. I'm not a newbie and have been on this board for a while)
Last edited by WildThing94Z; Mar 30, 2004 at 12:52 PM.
Registered User
Joined: Jul 2002
Posts: 1,193
From: San Diego, CA
(don't know why the post count is so low and Junior member is there. I had @ 750 posts since the last time. I'm not a newbie and have been on this board for a while)
Just FYI, they had a problem with the board a few months ago and lost the post count data for some people (mostly old members 1998 and such). There is info in the board suggestion area. You can email Jason/Chris and they can fix it. Just incase the post count mattered to someone.
And too bad you aren't selling these a month from now, they are mighty appealing.
Just FYI, they had a problem with the board a few months ago and lost the post count data for some people (mostly old members 1998 and such). There is info in the board suggestion area. You can email Jason/Chris and they can fix it. Just incase the post count mattered to someone.
And too bad you aren't selling these a month from now, they are mighty appealing.
