355cid,afr 190cc, forged pistons, "10sec motor in 3400lbcar" "non lt1"
12-05-2003, 08:07 PM
#1
Registered User
Thread Starter
Join Date: Oct 2001
Location: eatonton
Posts: 80
355cid,afr 190cc, forged pistons, "10sec motor in 3400lbcar" "non lt1"
· 355cid 9.45:1 comp
· Fully balanced rotating assembly
· Stock rods with ARP bolts
· Stock crank with polished journals
· Probe Industries Forged Pistons
· Dura-Moly Rings
· Rollmaster True Roller Timing Set
· Melling High Volume Oil pump with arp stud
· Stock oil pan
· Pro Race balancer
· Stock flex plate
· Stock Timing Cover
Valvetrain:
· Comp Cams Roller Lifters
· Comp Cams Pushrods
· Comp Cams Xtreme Energy Cam 224-230dur@ 50 .530-.540 lift with 1.6rr
· Summit 1.6 Roller Rockers
· AFR Springs up to .550 lift
Heads:
· AFR 190cc Heads, clean up work after cnc porting, flow 268int and 200 exh
· Manley int valves
· REV exh valves
· AFR locks and retainers
· AFR guide plates and rocker studs
Car ran 10.70's on nitrous at sdr and a has run a best of 7.62 in the 1/8th all motor which is equal to an 11.94 in the 1/4. I am asking 2600.00 obo for the motor. you can e-mail me or call me at 478-457-7503 I also take paypall as well..
Drew
· Fully balanced rotating assembly
· Stock rods with ARP bolts
· Stock crank with polished journals
· Probe Industries Forged Pistons
· Dura-Moly Rings
· Rollmaster True Roller Timing Set
· Melling High Volume Oil pump with arp stud
· Stock oil pan
· Pro Race balancer
· Stock flex plate
· Stock Timing Cover
Valvetrain:
· Comp Cams Roller Lifters
· Comp Cams Pushrods
· Comp Cams Xtreme Energy Cam 224-230dur@ 50 .530-.540 lift with 1.6rr
· Summit 1.6 Roller Rockers
· AFR Springs up to .550 lift
Heads:
· AFR 190cc Heads, clean up work after cnc porting, flow 268int and 200 exh
· Manley int valves
· REV exh valves
· AFR locks and retainers
· AFR guide plates and rocker studs
Car ran 10.70's on nitrous at sdr and a has run a best of 7.62 in the 1/8th all motor which is equal to an 11.94 in the 1/4. I am asking 2600.00 obo for the motor. you can e-mail me or call me at 478-457-7503 I also take paypall as well..
Drew
Last edited by Nosfedgta; 12-05-2003 at 08:11 PM.
12-22-2003, 05:00 AM
#4
Registered User
Join Date: Jun 2001
Location: Hinesville, GA
Posts: 1,192
I'm interested in the heads if you're willing to seperate. Those flow numbers look stock for AFR's, do you know what they flow now? Pics? any more info? dhirocz@yahoo.com
12-23-2003, 09:27 PM
#5
Registered User
Thread Starter
Join Date: Oct 2001
Location: eatonton
Posts: 80
those numbers are the exact numbers. when i got them from afr they flowed 254int and 189 exh. I had some clean up done. And that is the result I got. As of now I am not seperating the motor. I am trying to sell it whole. I still cant beleive that nobody has stepped up yet. You could never build it this cheap. Plus look at the numbers it ran!! Its one bad azz motor for only 2600.00
Drew
Drew
Thread
Thread Starter
Forum
Replies
Last Post