Which plate are you running in your exhaust? I have the smallest in there and it is really blatty. Someone told me that the open one is blatty too. Any suggestions?

------------------
1997 Trans Am WS6
White, 4A, K&N, TBbypass,
MAF mods, 160* stat., Air Foil, Borla Cat-Back, Black T/A side decals and rear fill-in by Firebat
Best ET to date: 13.723@103.09
60ft: 2.043

1982 Pontiac Firebird
2.8 V6, A4, t-tops, American Racing Rims - PROJECT CAR

Check them out at http://communities.msn.com/MyFbodyPage

"I live with fear everyday, sometimes she lets me race"

 

Yeah, here's a suggestion, Borla sucks and Corsa rocks! Just messing with ya!

------------------
Grand Rapids, MI
2002 WS6
http://www.sigma-epsilon.org/steve
stevedertien@attbi.com
Whisper Lid, Grotyohann Headers and Y-pipe, Corsa Exhaust, BMR SFC's, McLeod Single Disk, Spohn Torque Arm, LCA and Panhard Rod and much more to come

 

My plates are all sitting on a shelf in my garage, until i get headers i'm running it wide open. Then i may use the smaller one.. but prolly not..

------------------
Chris
------------------
'98 Black Z28 M6
Lid, EGR Mod, Borla Exhaust
SLP Short Throw & ****
-------------
http://cpfarhood.tripod.com
AIM: CPFarhood

*Boycot Roseville*

 

I also have a Borla and got tired of changing the plates. The top bolt on them is a bitch to get off. So I bought and electirc cut out. I can adjust my sound and performance at the flip of a switch in five seconds while I sit on my azz. www.quicktimeperformance.com

------------------
~Rich
95 Arctic White Z~28

 

My friends gotta Borla on his third gen.He has Hooker longtubes and a borla catback.It is really blatty with it wide open.With the plates in it tones it down.I am a flowmaster fan my self.IMHO Nothing beats the sound of an American V-8 rumbling through a set of 2 chamber Flowmasters. Thank You.

------------------
91 Z-28 Convertible 305 H.O. 210 RWHP
crane hi-6,holley reg,air foil,3:73 richmonds,Ed Wright stage 2 chip,msd wires,SLP headers,best e.t 14.4@99.02mph

91 Mustang 5.0 LX Convertible. A4, FMS 9mm plug wires, Denso Plugs, Other than that STONE STOCK AND SLOW!!!

(Retired 1995 S-10 Blazer 4X4, 230,000 Mi
Leland RD burnout Champ!!!)

 

cut a piece of sheetmetal in the same shape as the plates. Drill a 3/4 inch hole in the middle of it. 3/4 is the best size hole.



------------------
Rick
1991 White Mustang GT, T5 (2.95 1st, converted AOD), King Cobra, Tri-Ax, Fortes, Hedman 1 5/8" shorties, LX taillights, K&N, Hawks Pulleys, 2 1/2" off-road H, dumped 2 chamber Flows, FMS 3.73, FMS aluminum driveshaft, 2000 GT suspension, deleted: !tailpipes, !smog, !AC, !spare and jack, !foglights and bracket, !various insulation, pumpkin dog bone

1995 Black Camaro Z-28 M6, bolt-ons, NX@150hp (SOLD and missed)
2001 Black Dodge Durango R/T 5.9 AUTO

like my girl says.... "don't playa hate, participate"