Dropping a LT1 in a 80 Malibu
Dropping a LT1 in a 80 Malibu
Hello all, my name is matty man and I am getting ready to drop in a LT1 in a 80 Malibu. I am on Maliburacing web site a bunch and a few people recommended this web site for helpful insite on the Malibu project. The engine is a 94 LT1 out of a cop car, was susppose to be rebuilt @ 100K and it had 130K before getting T-boned in the pass side. I have read through some of the post here and this seems to be a great site for my many questions on this new adventure. So if you have any suggestions, ideas let me know,, Hope to be asking many questions soon, matty man
Hi Matty, me and my brother just got through looking at a 78 malibu and was talking about droping an LT1 in it. Oh yeah this is a great site I have got alot of information from it. Best of luck with your G body
later
Josh
later
Josh
You might find these sites much more helpful :
LT1 into a 78 Malibu :
http://www.carcraft.com/howto/81518/index.html
LT1 into a 2nd gen Camaro :
http://www.geocities.com/hardimon01/Conversion.html
2nd gen Camaro forum (look for the LT1/LS1 section) :
http://www.nastyz28.com/forum/index.php
Trans mount :
http://www.bowtieoverdrives.com/index.shtml
LT1 A/C Comp Relocate Kit :
http://www.bowersrodshop.com/home.htm
I am doing an '94 LT1/4L60E into a '78 Camaro.
Tom
LT1 into a 78 Malibu :
http://www.carcraft.com/howto/81518/index.html
LT1 into a 2nd gen Camaro :
http://www.geocities.com/hardimon01/Conversion.html
2nd gen Camaro forum (look for the LT1/LS1 section) :
http://www.nastyz28.com/forum/index.php
Trans mount :
http://www.bowtieoverdrives.com/index.shtml
LT1 A/C Comp Relocate Kit :
http://www.bowersrodshop.com/home.htm
I am doing an '94 LT1/4L60E into a '78 Camaro.
Tom
Last edited by sbca96; Jan 14, 2007 at 05:43 AM.
I installed a '96 LT1 in my '84 Grand Prix.
Check this link for an LT1 swap in '87 Monte Carlo SS.
http://home.comcast.net/~spudmanmike/scrapbook.pdf
Check this link for an LT1 swap in '87 Monte Carlo SS.
http://home.comcast.net/~spudmanmike/scrapbook.pdf
Thanks for all the great links, looks like a good swap, should keep me jumping! The plans for the car will be a frame off restro, its a Fla rust free car with the interior shot, it will be the LT 1 eng, 700R4 tranny and the rear is up in the air right now. I am going to install the non-AC set up in this Malbu so I dont need the compressor. My 1st step is to ensure this engine is not the 4.3 lt, I will ck the #`s on the block.
One of my main goals is to run a hot rod shop based on GM cars, mainly A/G bodies, I work at Classic Resurrection now at night, ( a goverment slug during the day) and we do retros on 55 to 57 chevys mainly but we do almost anything, This will be my 1st LT 1 in an A/G body, should be fun,, Again thanks for all the great links, matty man
One of my main goals is to run a hot rod shop based on GM cars, mainly A/G bodies, I work at Classic Resurrection now at night, ( a goverment slug during the day) and we do retros on 55 to 57 chevys mainly but we do almost anything, This will be my 1st LT 1 in an A/G body, should be fun,, Again thanks for all the great links, matty man
Thread
Thread Starter
Forum
Replies
Last Post
dbusch22
Forced Induction
6
Oct 31, 2016 11:09 AM
Sixer-Bird
Automotive News / Industry / Future Vehicle Discussion
34
Aug 31, 2002 12:59 PM
Sixer-Bird
Automotive News / Industry / Future Vehicle Discussion
10
Aug 25, 2002 01:12 AM



