LS1 Based Engine Tech LS1 / LS6 / LS2 / LS3 / LS7 Engine Tech

Front Turn Signal

Thread Tools
 
Search this Thread
 
Old Sep 29, 2002 | 11:54 AM
  #1  
Z28-CTYHNTR's Avatar
Thread Starter
Registered User
 
Joined: Jul 2002
Posts: 180
From: Lewisville, TX USA
Angry Front Turn Signal

My driver side turn signal is out, its bad enough its already out and I havent even had the car 5 months, but its impossible to get to it to change it! How can I get to the turn signal light? I tried taking off the headlight but I couldnt figure out which bolts where holding it on. Im guessing I would have to get under the car to do it? If anybody knows please tell me
Old Sep 29, 2002 | 12:31 PM
  #2  
JackZ.Twenty8's Avatar
Registered User
 
Joined: Mar 2000
Posts: 544
From: H-town, TX
All you have to do is take off the headlight, feel for the bulb, and twist it out. Then you just replace the bulb and twist it back on. It's simple, really!
Old Sep 29, 2002 | 12:36 PM
  #3  
Bloodztone's Avatar
Registered User
 
Joined: Jul 2001
Posts: 663
From: San Antonio, Texas
Yes you'll have to get under the car and unscrew the flap by the tires (make sure you're not right under it when you bring the flap down, a lot of dust and junk gets in there). There should only be two screws there and the flap will come down. Once there you'll see the housing and wire for the bulb. There should be a gray latch that you pull out and away from the housing to unscrew the bulb. Once you do this the bulb will come out really easy. It's just tough finding that little latch. That should do it and it'll will be a snap to do next time.
Old Sep 29, 2002 | 02:17 PM
  #4  
Dark Angel's Avatar
Registered User
 
Joined: Oct 2001
Posts: 765
From: Henderson, NV
I usually pull the headlight, much easier then climbing under the car. There is 1 10mm bolt at the back under the bracket going to the radiator support. Remove that and slide the headlight towards the center of the bumper and you should feel it come loose. Then just pull it out and you have plenty of room to do what you need. Installation is reverse of removal.
Old Sep 29, 2002 | 02:45 PM
  #5  
nikkev's Avatar
Registered User
 
Joined: Nov 2000
Posts: 747
From: Charleston,SC
Here's a bad pic of the one bolt you have to take out.It's 10mm.It's the bolt-head that you can see right under the black bracket.Good luck.You'll have to cut and paste the link because it's geocities.
Kevin

http://www.geocities.com/nikkev1/Pics/clearinstall6.jpg
Old Sep 29, 2002 | 02:49 PM
  #6  
Z28-CTYHNTR's Avatar
Thread Starter
Registered User
 
Joined: Jul 2002
Posts: 180
From: Lewisville, TX USA
Lightbulb

Thanks a lot for all your help guys, Ill go try it out right now
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
dbusch22
Forced Induction
6
Oct 31, 2016 11:09 AM
stangspank
Car Audio and Electronics
3
Nov 13, 2015 01:02 PM
Ryabut98
Car Audio and Electronics
4
Sep 3, 2002 11:45 PM
vinnyxgunz
Car Audio and Electronics
5
Aug 28, 2002 09:41 PM
CMJ917-95CMO
Automotive News / Industry / Future Vehicle Discussion
3
Jun 19, 2002 09:10 PM




All times are GMT -5. The time now is 05:24 AM.