Wings West SS Spoilers Guys come inside
#1
![Question](https://www.camaroz28.com/forums/images/icons/icon5.gif)
Goot mine painted and put on my 98 yesterday, looks great but the two middle post do not touch the car they stick up and have a 1/4 inch gap. Any way to fix this? I am sure some of you guys have encountered the same thing.
Viper
Viper
#2
![Post](https://www.camaroz28.com/forums/images/icons/icon1.gif)
Look at the spoiler from the side...if you notice the spoiler is not even with the body, then u need to take it off and start grinding away at the bottom of the spoiler...The hole that the wire from the 3rd brake lights goes into on the rear deck lid you will have to grind flat...
------------------
Keith '00 "Heritage" SS
My LS1
Rate My Ride
Email: SweetSS@cfl.rr.com
CFFB#127
Mods:
SLP Loudmouth Exhaust, Lou's Short Shifter, Carbon Fiber Lid, K&N Air Filter, !EGR, !FRA, Custom STB, OEM Z06 Rims, Intrax 2" drop, billet grille, LS1 Hot Cam, GFX, WW 98+ SS Spoiler, Ultra Z hood
House of Kolor Sunrise Pearl stripes...
------------------
Keith '00 "Heritage" SS
My LS1
Rate My Ride
Email: SweetSS@cfl.rr.com
CFFB#127
Mods:
SLP Loudmouth Exhaust, Lou's Short Shifter, Carbon Fiber Lid, K&N Air Filter, !EGR, !FRA, Custom STB, OEM Z06 Rims, Intrax 2" drop, billet grille, LS1 Hot Cam, GFX, WW 98+ SS Spoiler, Ultra Z hood
House of Kolor Sunrise Pearl stripes...
#3
![Post](https://www.camaroz28.com/forums/images/icons/icon1.gif)
Yes, the WW SS spoiler fits like crap. I went through three of them. The first one fit really bad, so they sent me another claiming they knew of the problem and the mold had changed. the only thing that changed was the hole for the wires were pre cut. the second one crack at the front edge. the 3rd one I sold to get my money back.
you can't grind the spoiler down far enough to make it even. the mounting pads aren't thick enough. you can get it close though. don't gind the deck lid opening for the wires. enlarge the hole on the spoiler or it will leak.
------------------
Rick
'65 Malibu SS - 280rwhp/330ftlbs
'98 Camaro Z28 - 318rwhp/334ftlbs - Sold 7-18-02
'02 TransAm - Brand new No dyno Yet
D-flo lid, GMS, Hotchkis STB, Hurst B+
Bat-CaveOnline
you can't grind the spoiler down far enough to make it even. the mounting pads aren't thick enough. you can get it close though. don't gind the deck lid opening for the wires. enlarge the hole on the spoiler or it will leak.
------------------
Rick
'65 Malibu SS - 280rwhp/330ftlbs
'98 Camaro Z28 - 318rwhp/334ftlbs - Sold 7-18-02
'02 TransAm - Brand new No dyno Yet
D-flo lid, GMS, Hotchkis STB, Hurst B+
Bat-CaveOnline
Thread
Thread Starter
Forum
Replies
Last Post
94z28jbw
Site Help and Suggestions
2
09-08-2002 03:22 PM
johnsocal
Automotive News / Industry / Future Vehicle Discussion
4
06-22-2002 12:18 PM