1991 Z28 with lots of goodies

Thread Tools
 
Search this Thread
 
Old Dec 2, 2006 | 11:39 AM
  #1  
Kado91Z's Avatar
Thread Starter
Registered User
 
Joined: Mar 2006
Posts: 40
From: Grand Rapids, Mi
1991 Z28 with lots of goodies

Car is a 1991 Z28. T-Top car. originally was 305/700r4. The odo reads 200k miles but it was repainted recently. Also the motor has about 10k. Body has small dents here and there and previous owner painted over some stripes on drivers side door, but not very noticeable from 10 feet. rear bumper support rusted out so will need replaced. Previous owner installed 6 point cage. Has grey interior, carpet has stains in the fronts but overall interior is very very clean.

Floorboards had rust on them but i stripped them with a wire wheel and then POR 15'd back to the rear end.

-installed new 255lph fuel pump about 1000 miles ago
-installed new front to rear brake line after original broke.
-new posi/3.73 10 bolt installed. Has PBR disc brakes and axle tubes welded.
-original Z28 wheels stripped and polished.
-has custom y pipe and single 3 inch exhaust, no cats, hooker aerochamber single 3 inch inlet/outlet muffler.

If i sell the parts separate these would be my prices.

T-56 Tranny with pedals, centerforce 2 piece RMS 153 tooth flywheel, clutch, hydraulics. unknown mileage $1500 pickup only

400 bare block all machined and ready to be assembled. Bored .030 over, honed, magged, decked etc. 817 casting 2 bolt mains $650 pickup only

DART Iron Eagle Platinum Series heads. 200cc runners, 64 cc chambers springs good to .600 lift. $730 shipped

Edelbrock Victor Jr heads. 215cc runner 64cc chamber. Also custom CNC port work done. Also comes with brand new titanium valves and springs good to .630 $1000 + shipping

Holley Stealth Ram Injection setup. includes polished plenum, base, fuel rails, 24 lb injectors(cost $150), Kirban adjustable billet FPR(cost about $100), SS braided fuel lines, vacuum fittings, t stat housing, small cap distributor $700 for it all

BBK 52mm throttle body for 90-92 TPI $200

Hooker Super Comp 1 3/4" ceramic coated headers. Have some dents in them for starter and #7 plug but overall very good condition. $175 + shipping

Moroso high capacity oil pan for 82-92 f body with 2 piece RMS. painted VHT red $100+ shipping


Right now the car runs and drives fine, has a 357 with the dart heads, HSR on it but i think it will need new bearings cause the oil pressure gets to about 10 psi at idle when its warm. Has the 700r4 also installed right now but it is tired. Had a custom tune done by a thirdgen member when the motor went in but could use another tune to put out even more power. i wouldnt be afraid to drive the car anywhere though. I was going to do a 406/T56 swap this winter but am too busy with school and work and i need the money for an apartment.

Right now i would really like to sell everything as a package for someone to finish what i started. If theres enough interest in all other parts may sell it as a roller. total package with all parts listed i would start at $7500 obo
Im sure theres even more new stuff i cant think of right now.

Last edited by Kado91Z; Dec 2, 2006 at 11:47 AM.
Old Dec 2, 2006 | 11:46 AM
  #2  
Kado91Z's Avatar
Thread Starter
Registered User
 
Joined: Mar 2006
Posts: 40
From: Grand Rapids, Mi
e mail me at ZCap91@yahoo.com for pics and any questions/offers
Old Dec 5, 2006 | 11:24 AM
  #3  
Kado91Z's Avatar
Thread Starter
Registered User
 
Joined: Mar 2006
Posts: 40
From: Grand Rapids, Mi
price is not firm, will accept offers
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
DirtyDaveW
Forced Induction
13
Dec 1, 2016 05:37 PM
dbusch22
Forced Induction
6
Oct 31, 2016 11:09 AM
HectorM52
Parts For Sale
1
Jan 30, 2015 11:34 PM
A's 91 Z28
Fuel and Ignition
1
Jan 11, 2015 10:58 AM
1LEThumper
Forced Induction
40
Jul 14, 2003 12:45 PM




All times are GMT -5. The time now is 10:56 PM.