CamaroZ28.Com Message Board
After stripping the insulation off, I twisted the stranded wires, and tinned them (applied solder to the wires)
After stripping the insulation off, I twisted the stranded wires, and tinned them (applied solder to the wires)
0 2021/03/16 02:48:04
0 2021/03/16 02:54:50
The next morning I covered both wires with a 1/4" heat shrink tubing and shrunk that. I then stripped the insulation off the remaining ends.
The next morning I covered both wires with a 1/4" heat shrink tubing and shrunk that. I then stripped the insulation off the remaining ends.
0 2021/03/16 02:54:52
what should be seen checking from each wire to the case. This is an open or infinite resistance reading.
what should be seen checking from each wire to the case. This is an open or infinite resistance reading.
0 2021/03/16 03:01:09
Typical resistance reading across the two wires.
Typical resistance reading across the two wires.
0 2021/03/16 03:01:12
0 2018/07/29 20:08:01
The sensor installed in the sensor mount. This mount goes into the top of the rear end housing.
The sensor installed in the sensor mount. This mount goes into the top of the rear end housing.
0 2021/03/16 03:11:09
0 2021/03/16 03:15:20
On the left is a 22 gauge wire assortment I purchased from Amazon. On the right is a heat shrink tubing assortment I purchased from Home Depot. Individual heat shrink tubing sizes are also available in smaller quantities in various sizes.
On the left is a 22 gauge wire assortment I purchased from Amazon. On the right is a heat shrink tubing assortment I purchased from Home Depot. Individual heat shrink tubing sizes are also available in smaller quantities in various sizes.
0 2021/03/16 03:19:06
Driver's side sway bar mount. I got 2" square 1/8" thick steel square stock. Cut to 4-1/2", drilled 5/16th" holes on the centerline with hole center 23mm from one end then 3" on center for the other hole. Bolted with 3-1/2" 5/16-18 bolts (3" would have been enough).
Driver's side sway bar mount. I got 2" square 1/8" thick steel square stock. Cut to 4-1/2", drilled 5/16th" holes on the centerline with hole center 23mm from one end then 3" on center for the other hole. Bolted with 3-1/2" 5/16-18 bolts (3" would have been enough).
0 2021/07/08 16:57:20
Same procedure as driver's side.
Same procedure as driver's side.
0 2021/07/08 16:57:22
I found this vent tube at Grainger.com It is part number 1U570 and they called it Protected vent 1/4. height 1.19. It screwed right into the hole provided by Moser Engineering.
I found this vent tube at Grainger.com It is part number 1U570 and they called it Protected vent 1/4. height 1.19. It screwed right into the hole provided by Moser Engineering.
0 2021/07/08 16:57:24
The bottom torque arm bolts.
The bottom torque arm bolts.
0 2021/07/08 16:57:26
The top torque arm bolts
The top torque arm bolts
0 2021/07/08 16:57:28
The passenger side brake brace. The Driver's side is similar.
The passenger side brake brace. The Driver's side is similar.
0 2021/07/08 16:57:30
The t-block for the left and right hard lines and the main supply line. I drilled a 5/16" hole in the center bracing.
The t-block for the left and right hard lines and the main supply line. I drilled a 5/16" hole in the center bracing.
0 2021/07/08 16:57:32
0 2023/07/07 14:29:41
0 2023/07/07 14:29:46
0 2023/07/07 14:29:51
0 2023/07/07 14:29:55