tons of parts for sale...stock performance suspension Built LT1/Chevy Blazer
07-29-2009, 03:51 AM
#1
Registered User
Thread Starter
Join Date: Nov 2004
Location: Garland, tx
Posts: 2,475
tons of parts for sale...stock performance suspension Built LT1/Chevy Blazer
ls1 rails 40
injectors 34 lb/hr and 60 psi (flow tested with sheet) 250
boxed LCA with poly/poly bushngs 75 bux
stock ls1 rockers 65
stock maf 60
flexplate 50
stock delco amp...50
stock monsoon radio....75
94 lt1 timing cover...25
black leather door panels perfect...250
passenger ttop 100
3.42 rear end quiet and 48k on it 300
3.73 rear makes some whining 375
cc306 6k miles.....210 shipped
crane dual 10308 vale springs 175 shipped
ls1 centerforce dual fristion clutch brand new in box 275
also have many interrior pieces from parting out a 1999 and 2000 z28
got a few NBM doors/hatches
couple dashes with blown airbags
brake lines
fuel lines
gas tanks
k members
struts
shocks
spindles
brakes
steering columns
interrior pieces
complete tan interrior/seats/plastics ect
swaybars phb's lca's
359 ci LT1 this shortblock is from Jim Moran aka "INTMD8" His car was well known for the fact that it was a very clean streetable(A/C, T56, full interior) turbo car for the power it was making. To give you an idea, with this shortblock he dynoed 890rwhp/855rwtq, ran a best of 9.68@146, and did 199mph in the standing mile.
Specs:
359ci LT1. 3.5in stroke forged Eagle crank, 6.0in Eage H-beam rods, 4.040 bore CP reverse dome pistons -23cc., Hellfire rings, Clevite H bearings, Internally balanced. Block has 3 center mains splayed 4 bolt. It was freshly rebuilt when I purchased it, including an align hone, new bearings/rings, and the crankshaft was turned .010 under.
asking $2000
1998 chev Blazer 4x4 150k miles red exterrior grey leather fully loaded heated seats needs ac compressor(ill fix if buyer pays for parts) also needs a few small things such as door switch(keeps inside lights on) and one speaker doesnt work
2000
wtb/trade
ls1 6 speed /twin disk clutch
dual ls1 valve springs
hardened pushrods
powerglide/converter
injectors 34 lb/hr and 60 psi (flow tested with sheet) 250
boxed LCA with poly/poly bushngs 75 bux
stock ls1 rockers 65
stock maf 60
flexplate 50
stock delco amp...50
stock monsoon radio....75
94 lt1 timing cover...25
black leather door panels perfect...250
passenger ttop 100
3.42 rear end quiet and 48k on it 300
3.73 rear makes some whining 375
cc306 6k miles.....210 shipped
crane dual 10308 vale springs 175 shipped
ls1 centerforce dual fristion clutch brand new in box 275
also have many interrior pieces from parting out a 1999 and 2000 z28
got a few NBM doors/hatches
couple dashes with blown airbags
brake lines
fuel lines
gas tanks
k members
struts
shocks
spindles
brakes
steering columns
interrior pieces
complete tan interrior/seats/plastics ect
swaybars phb's lca's
359 ci LT1 this shortblock is from Jim Moran aka "INTMD8" His car was well known for the fact that it was a very clean streetable(A/C, T56, full interior) turbo car for the power it was making. To give you an idea, with this shortblock he dynoed 890rwhp/855rwtq, ran a best of 9.68@146, and did 199mph in the standing mile.
Specs:
359ci LT1. 3.5in stroke forged Eagle crank, 6.0in Eage H-beam rods, 4.040 bore CP reverse dome pistons -23cc., Hellfire rings, Clevite H bearings, Internally balanced. Block has 3 center mains splayed 4 bolt. It was freshly rebuilt when I purchased it, including an align hone, new bearings/rings, and the crankshaft was turned .010 under.
asking $2000
1998 chev Blazer 4x4 150k miles red exterrior grey leather fully loaded heated seats needs ac compressor(ill fix if buyer pays for parts) also needs a few small things such as door switch(keeps inside lights on) and one speaker doesnt work
2000
wtb/trade
ls1 6 speed /twin disk clutch
dual ls1 valve springs
hardened pushrods
powerglide/converter
Last edited by Daniel6718; 07-29-2009 at 03:56 AM.
08-12-2009, 11:34 AM
#6
Registered User
Join Date: Sep 2003
Location: The Wild West
Posts: 5,907
What all do you have off the front end suspension? I could use the spindles, upper and lower A arms, front brakes, etc. Oh, and I could come pick them up if that helps. Just PM me some prices on that stuff if you have it.
-Dustin-
-Dustin-
