This is the new thread that I am starting for B/CS car guys so that the other one doesn't get locked. Hope to see you all at car club!

------------------
95 White t-top Z28 M6 Mods include: Hotcam kit, Mac midlengths, flowmaster, Homemade CAI, airfoil, TB bypass, !EGR, !AIR and a B&M ripper shifter.

 

Man Aaron, I didn't know we were "members"...j/k. Seriously though, David told me he rode in your car last night. I will be out next wed at CC to see the racing so give me a ride if poss. My slow *** truck won't be able to keep up. Mid March is the date set to have mine done. You better be ready for some racing. WE will have some more races like your truck against my Camaro, me winning like always of course. Gotta talk some smack since everyone else has been

 

Sorry dude, but by mid march you probably won't want to run my car any more. I have a full time job and no bills, so where does my money go? I bet that by next march I will be somewhere in the low 11's to low 10's. I will be more than happy to take you for a ride in my car on wednesday, or this friday for that matter. I will be at hastings in bryan if you want to show up.

------------------
95 White t-top Z28 M6 Mods include: Hotcam kit, Mac midlengths, flowmaster, Homemade CAI, airfoil, TB bypass, !EGR, !AIR and a B&M ripper shifter.

 

I was there last night, tall guy with the silver V6 bird w/ GFX. Good to finally meet you all and hope to have fun these next 4 years.

BTW i also can't wait to see Hanz and Franz watch their orgy b/f out to run 1-BAD80Z and Rick. That's gonna be a riot.

Scott

------------------
2000 Silver stalled A4 Bird
soon to be slammed and cammed

 

"Hanz and Franz watch their orgy b/f out to run 1-BAD80Z and Rick"

LMFAO

jusitn

 

Does anybody have Tony's E-Mail address ??? Or phone # ???? Ed

------------------
New Sig. !!! 434 Small Block is now in the car !!! Ross lightweight flat top racing pistons ,( 11.5 Compression ), 6in. 4340 rods w/ARP wavelock bolts , 4340 Forged non-twisted steel crank , Solid Roller cam-260 Degrees ( @ .050 ) 270 on the exhaust , .610 lift w/1.5 Rockers. Fully ported Alum. heads , Ported Victor Intake , Barry Grant Carb. and three stages of N.O.S. ( 350 H.P. )Lots of shiny stuff and still a daily driver !!!

 

Rick , have somebody with a truck come along so we can swap out tires for the Hanz & Franz A$$holes !!! I want ANYBODY that is capable to SMOKE their A$$ !!!! Those two are COMPLETE A-Holes !!!! My new trans is already in the works !!! This time there won't be any mistakes !!!! Ed I have a floor jack to bring with to swap tires between races. We need to put this FOOL in his place !!! To claim a win because I smoked my trans is STUPID !!! I was THREE cars ahead when the tranny went !! AND he was spraying.

------------------
New Sig. !!! 434 Small Block is now in the car !!! Ross lightweight flat top racing pistons ,( 11.5 Compression ), 6in. 4340 rods w/ARP wavelock bolts , 4340 Forged non-twisted steel crank , Solid Roller cam-260 Degrees ( @ .050 ) 270 on the exhaust , .610 lift w/1.5 Rockers. Fully ported Alum. heads , Ported Victor Intake , Barry Grant Carb. and three stages of N.O.S. ( 350 H.P. )Lots of shiny stuff and still a daily driver !!!

 

Tony is a great guy and his car is very fast but he is not a BCS boy anymore...this is a BCS matter.
Rick

 

hmm

 

good luck!

 

I think that tony should come down. Even though he is not a BCS boy anymore, he should have some fun with them too. I would like to see anybody and their dog beat these two no matter where they are from. If I had more motor I would take them out too.

also, brook, if we keep on with the other page, they are just going to lock it anyway. We might as well start a new one.

Ed, do you think that your car will be ready in time for car club? I might have a friend who can carry your tires for you or rick.


------------------
95 White t-top Z28 M6 Mods include: Hotcam kit, Mac midlengths, flowmaster, Homemade CAI, airfoil, TB bypass, !EGR, !AIR and a B&M ripper shifter.

[This message has been edited by jimbo95Z28 (edited September 06, 2002).]

 

Ed and Rick, I will be in my truck if ya'll want to do the tire thing, just let me know. I am off on Wednesday so I can help ya'll out plus I want to see all the action. Look for the pewter reg cab Chevy 4X4, or Rick I will probably have Brittany S with me so you can just see her. And Aaron, you better have a 10 second car by March, b/c you will be racing one. Better learn how to shift that six speed. I prob won't be out on Friday but I will come out on Wednesday and catch up with everyone. Since I sold my Camaro I had pretty much quit going.

 

I don't know the guy, but he is a *****. I think he is one of Fred Brown's sons. I saw him and told him I had some things for the car like the t-top holders and shades, but he just blew me off so I sold them. He hasn't modded it yet, he said I had did all the mods he wanted. I tried selling him my CC305 but he didn't want it.

 

I wish that I had known that you had that 305. I would have bought it off of ya. Would have been a better cam for building a blower motor. Oh well. You had better have a 10 sec car too, just because I want some more guys whose cars have ***** out at car club. We have like 4 now. Well, i guess that I need to go back to work now.

PS brook, why are you so against starting a new thread? Just start posting here, it isn't like it's going to kill you.

 

Well,
I have had three diff people in the last two days say this guy has a 422 in it and one other guy that says he runs 9's with a 250 shot....
I am wondering now about this since the guy told me he only had a "bolt on" car. I did hear a really small cam in it but that doesn't mean he couldnt have alot of cubes...I have heard 382's with a small cam that sound like a bolt on car...
I think this guy might be hustling everybody...
Rick