Just so I make sure I have everyone on the list I'm going to write down(in order I recieved the posts) of who wants what. This is what I have so far:

1. Eddie - PHR and LCA's
2. Mark D. - PHR and LCA's
3. Predatorbird - LCA's
4. Camaro_Dakota - PHR and LCA's
5. stk350 - LCA's
6. Yoshi(Josh) - LCA's
7. Bad86Z28 - PHR and LCA's
8. DarthIroc

As of right now I have enough LCA's and PHR's to get the first 3 on the list finished by the end of this week. I will have the last 2 on the list done by the end of next week at the latest.

Is there anyone else that wants to join in on this? Once I get these order's done I'll have 3 sets of each(PHR and LCA's) laying around to make for anyone else. I'll probably go ahead and weld them up so if someone wants them I can just run them over

Thanks again guys for ordering them from me, it's definetly a help for me, I need any extra $ I can get to help pay for my mountain of medical bills.

 

I am interested in a PHR and some LCAs. On a side note, would you be able to weld up some SFCs? What would you want to do them? I might need to have a small plate welded to the back of my transmission cross-member too. You can email me with prices for the last two. Thanks.

 

hey mike,
dont froget about me!
remember i only want the lcas

thanks
josh

 

Looks good to me.



On a side note... I think I'll be picking up some stock manifolds off a '94 in a little while.

 

LOL, I'm not porting them for you! That took me literally like 20 hours to do my stock ones! I'm not doing that again unless you give me like $50

Bad86Z28 - I can't weld subframes under any circumstances unfortunatly. I don't have a lift or anyway to get under a car and weld stuff up, nor would I want to. Only because it's kinda dangerous, and I've never done it. If I had a lift I'd give it a shot, but I'm not getting under a car on jackstands and trying to weld!

Ok, the original post is edited, so everyone is on there. I'll keep working on making these things up for you guys!

 

remind me again about the prices?

 

$20 for just the LCA's, $15 for just the PHR, or $30 for both. This is a Florida only price If I start making them and shipping them out I'll charge a little more, but not too much.

 

You will do it wether you like it or not!

 

Then you will pay me $50(or give me something of equal value that I want) whether you like it or not!

 

lmao... HAHAHA

 

Welding on jackstands can't be that hard. I promise I'll make it nice and safe for you . I'll just take the PHR and some LCAs. If I brought you a tranny cross member could you weld a plate on to it and maybe some supports. If you have time I can show you exactly what I'm talking about.
BTW, if you don't recall, I'm Mark's friend, Bobby.

 

Yeah, I remember you Bobby, your name just slipped my mind earlier. Yeah, I can weld up your cross member, just let me know what you want done(either a drawing or just out a piece of cardboard the size and shape you want). I'll charge you according to the labor and materials used. And no, under no circumstances will I get under a car on jackstands and weld!! I already had one near death experience this year, that's one too many!

 

Thanks. I'll try to get you a drawing, probably, this weekend.

 

Anyone know the effectiveness of the LCAs, and Panhard as compared to say tubular Hotchkis models? Cause the price is sure competitive

 

For the price do it. Unless your into a certain look. It is sort of like a cut out or cat back.. Cut out will get you more so why not do that since it is cheaper.