Pics available for all parts. Paypal accepted on everything. Prices are WITHOUT shipping unless otherwise noted!!!

Moser 12bolt Rearend - SOLD

QA1 Rear Single Adjustable Coil overs. **edit- I now have all the parts, upper and lower brackets and upper reinforcement plates as seen on spohn.net** - $400 PENDING

front qa1 single adjustable coil overs off $350 PENDING

McLeod Twin Disk Clutch with 1k. Excellent condition with billet steel Flywheel - SOLD

Interior

Interior from a 94 Z28 available. Seats, pedals, steering column/wheel/drivers airbag, head unit, and door panels are gone. Other than that shoot me an email.

Perfect 93-96 Camaro charcoal-dark gray dash pad. No broken tabs, no cracks, all velcro in place underneath - $125

M6 93-96 Center Console, storage compartment under dash in good condition. No lid but has good hinge on console side to install a good lid to it. Ash tray hinge in good condition - $125

HVAC controls/*****/wiring pigtails - $35

150mph speedo w/140k on odometer - $35

Other misc parts upon request (other than those mentioned above that are gone) -$$$


Stock

(3) Stock 94-97 Fuel rail sets - $20ea 1 Set sold!
(1) Set of stock 94-97 LT1 Injectors - $35
(1) Stock 94/97 Throttle body, iac housing, & sensors - $40
(2) Accessory Bracket F-body - $25
(1) Set of LT1 Fans - $75
(2) LT1 Radiators - $50
(3) Stock Camaro Starters - $35ea
(2) Set of 643 heads - $185
(1) Set of stock valve covers clearanced for 1.6 roller rockers - SOLD
(1) Sets of stock valve covers - $15
(3) 95 LT1 Timing Covers - $75ea
(1) 95 LT1 Timing Cover with water pump hole tig welded shut, painted gloss black - $75
(1) 96/97 Timing Cover - $60
(1) 96/97 Timing Cover with water pump hole tig welded shut, painted gloss black - $60
(2) 92-94 Timing Covers - $20ea
(1) NEW 92-94 Timing Cover $30
(2) Sets of F-Body Exhaust Manifolds - $35ea
(2) OBD I PCM's (Service numbers ending in 8051) - $75ea
(1) Factory Oil cooler, comes with lines and adapter - $35 PENDING
(1) 94-97 Intake ported for 58mm TB & glass beaded clean - $75
(1) AC Delco Water Pump with only 2k, Looks new - $100
(2) LT1 Oil pans, with rails- 35ea
(2) LT1 3.5" (F-body & Y-body) MAF Sensors- SOLD(unscreened) & $50 (screened)
(1) F-body ABS Block - $50
(2) W/P driveshaft-gear-bearing - $25
(2) Oil pump driveshaft stub for rear of LT1 (looks like the bottom of a normal sbc dist) - $25
(2) Lifter retainers, spider, and cam retainer (sold as a kit) - $35
(1) Rear main seal holder - $20
(2) Harmonic balancer and hub set from f-body - $35


Performance

Taylor OTVC plug wires with NEW mounting kit (red wires, black mounts) - $75
Jegs SFI Approved Harmonic balancer & Pulley for LT1 - $50
Lingenfelter CAI tube (I only have the tube) - $40
GTS Black outs for front of F-body - SOLD
New in the box Melling oil pump w/driveshaft PN 10555- $20
Fabric Non-Woven Car cover, near new, blue, for F-body 93-02 - $40
Corvette Fuel Rail Covers that have been clearanced for use on F-body, includes studs - $70
Brand new in the box Comp Cams Solid roller lifters for LT1 & Late model 87+ SBC PN#888-16 - $400
http://www.summitracing.com/parts/CCA-888-16/
LS7 Lifters with 2k, perfect condition - SOLD
Comp Cams 875-16 'R' Series lifters with 1k - $100
http://www.summitracing.com/parts/CCA-875-16/
Holley 58mm TB for 94-97, includes gasket and sensors - $250
LT4 Intake coated gloss black with POR 15, Stage III ported for monoblade - $375
42lb Flowmatched Greentop injectors - $210
44lb Flowmatched Bosch Injectors - $225
37lb Lucas Injectors - $185shipped
38lb Lucas Injectors - $190shipped
Modified LT1 fuel rail for AN fittings, and enough AN lines and fittings to hook into fuel system beneath car to eliminate all plastic lines leading up to the engine - $175
BRAND NEW Weldon 2040 -120 Adj Fuel press reg for use with above setup - $175
Trickflow ceramic coated elbow - $60
Trickflow Black coated elbow - $50
ARP 12pt Head studs - SOLD
LTCC setup with LS1 Coils, only 3k, had new LS1 coils 3k ago, not used pullouts, Comes with custom brackets to mount where the fuel rail covers normally are, and a full set of taylor sparkplug wires with protector sheeths - SOLD
MSD coil for 93-95 F-bodies, plug and play - 25
Brett Bauer Cam Designed for 383 (Specs to those interested, 24x/24x & .60x/.60x) - $150
Walbro 255lph fuel pump mounted in F-body canister - SOLD
Meziere H20 pump, 160 hypertech thermo, in factory housing -SOLD
NIB 02 sims fit 97-02 Camaros - $85
http://fasttoys.net/shop/product_inf...60863830b368f4
Corvette Composite Valve Covers w/hardware - SOLD
AKM OBDI unmolded Cable (for 95 F-body or 94/95 Y-body)- SOLD
AKM OBDI molded Cable for 93-94 F-body - $50
Spohn Poly Motor mounts already in cages - SOLD
Hotchkis Boxed Poly Lower control arms (Black or red available) - $125
http://www.hotchkis.net/f_or_gbody_l...ling_arms.html
ATI Super Damper F-body Part # 917270 - $300

 

Are the head studs used, and what about the cloyes 3145?

 

Yep they have been used once. They are not torque to yield so can be reused tho.

 

Can I get a pic of the intake?

 

Here are a couple pictures, sent you a pm also...

 

need pics for Poly Motor mounts and ATI Super Damper F-body ddr698 i need a deal man i've bought a lot of stuff from you lol give me a good deal on this!!!!

 

Here are some pics.... shoot me a pm if you are interested in them. I also have a brand new ATI damper also if you are looking for a perfect one. (the used one has a little surface rust on it).

 

Any pics available of the fuel rails and lines? Thanks.

 

Please send me a pic of one of your 96-97 timing covers. PAYPAL ready. Thank you.

 

Interested in the stock injectors. PM sent

 

Do you have stock plastic fuel lines?
shipping to 21918?

 

The 4 of you have pms!

 

how much for shipping on a set of fuel rails to 89183 ?

 

Sent a pm your direction.
Up top!

 

do you still have the front QA1 coilovers, if so, can you email pics to khojo16@comcast.net