FOR SALE: Entire project, car, eng, trans, etc!!
Thread Starter
Registered User
Joined: Feb 2005
Posts: 610
FOR SALE: Entire project, car, eng, trans, etc!!
Please note that I posted a similar thread several months back but never ended up selling anything. I ended up leaving the country and came in to a little cash so I decided to keep. Now its several months later and I am super broke and the project still sits so its got to go. Depending on what kind of deal is worked out I can have any of this stuff other than the car shipped within a day or two of payment!
....
PM me with pic requests and I will take whatever you need. All parts listed are new unless stated. I would prefer to sell the whole setup at once, maybe split the car / engine / trans but not the parts. The only way I will sell parts piece by piece is if the engine itself sells.
The Car: (complete minus engine / trans)
1996 black z28 w/ T-tops and RS spoiler Roller with mint black leather interior <70k on the car.
Hotchkis front shocks.
LMP rear sway bar
boxed LCAS
Welded SFC
10 bolt with TA girdle.
Gas tank has sump welded in with AN fittings out/return.
a1000 fuel pump with braided lines installed all the way to the engine compartment. No plastic or rubber lines!
New 100 micron and 10 micron filters included (these aren't cheap!)
Scan master installed in center vent.
Autometer pillar with fuel PSI guage and a boost guage. Also contains the autometer electronic fuel guage sending unit.
OBDI and OBDII computers and wiring harnesses. Right now OBDII is installed.
SPOHN torque arm
*buyer of the car can also have my cherry picker
The Engine:
383 stroker longblock brand new never fired
Heads have been decently ported but unfortunetly I do not have flow #'s.
Eagle cast crank
eagle forged rods
SRP forged pistons
LT4 hotcam kit
Aeromotive 13101 FPR - ($140 @ Summit)
TCI neutral balanced flexplate (engine is internally balanced) - ($75 @ Summit)
proform chrome valve covers ($210 @ Summit)
Lunati double roller timing chain already clearanced etc.. ($85 @ Summit)
ASP Billet damper / keyed hub ($150 dampner @ Summit / $100 for hub @ ASP)
Milodon oil pan for 383 with windage trey (~$200 @ VRE)
Mezeir HD elec water pump installed on housing. ($275 @ Summit)
Race ported LT1 intake powder coated red with blockoff plates installed.
Holley 58mm TB ($399.95 @ Summit)
36lb Lucas Injectors installed & 50lb Injectors not installed (~$300 for the 36ers @ ??)
Fuel rails have AN fittings welded on to accept the fuel lines in the camaro
Jet Hot LT (used in good shape) w/ new stage 8 locking bolts and reusable gaskets. ($300 @ private seller)
New optispark with pigtail ($309 @ Summit)
Over the valve cover wire loom kit with tailor cut to fit wires. (I only cut and installed one side so far) ($110 @ Thunder racing)
Moroso CAI (slightly used) ($100 @ Private seller)
Vortech polished elbow ($118 @ Summit)
NEW MAF
full set of TR-55 and TR6 plugs included. ($59 / ?)
*buyer of the engine will also recieve the engine stand it sits on.
Transmission:
Race built TH400 to handle 1000+HP (used 600 miles)
Reverse Manual Valve Body
Its got an aftermarket bellhousing installed as well. Can't recal the brand but its top notch. I will get the part # and look it up.
Electric external tranny cooler with fan and all braided lines.
Billet dip stick with braided line.
Vigilante 3300 stall
Custom steel 3" driveshaft to fit stock 10bolt with the TH400
B&M ratchet shifter
Nitrous:
I have a nitrous system I would like $450 for. It includes NX bottle with custom graphite paint job, NX purge, NOS bottle warmer, console switch panel for arming, MSD window switch, NX shark nozzle, all wires and lines required for installation. I paid $650 for this used but he guy claimed it was a $1100 kit. I will take pics if interested.
So heres the deal. I would like to sell the engine as one, tranny as one, and car as one. I don't want to split apart anything listed under those three categories. $6000 takes everything, I have double that invested.
If bought seperately...
car - $1500 firm (this car is beautiful!)
Engine $3750 OBO
Trans - $1500 OBO
Nitrous - $450 OBO
The best deal is the engine; the extra parts add up to over $2900 without even counting the engine, rods, crank, complete hotcam hit, heads, custom intake and fuel rails, etc.. I am selling this for half of what it costed!!!!
PM me or email me at dr1ft0r@yahoo.com. I can give my cell # to anyone interested, just ask
ENGINE:
Before I bought all the extra stuff
After some stuff
oil pan and engine mounts / jet hot headers
extra stuff
....
PM me with pic requests and I will take whatever you need. All parts listed are new unless stated. I would prefer to sell the whole setup at once, maybe split the car / engine / trans but not the parts. The only way I will sell parts piece by piece is if the engine itself sells.
The Car: (complete minus engine / trans)
1996 black z28 w/ T-tops and RS spoiler Roller with mint black leather interior <70k on the car.
Hotchkis front shocks.
LMP rear sway bar
boxed LCAS
Welded SFC
10 bolt with TA girdle.
Gas tank has sump welded in with AN fittings out/return.
a1000 fuel pump with braided lines installed all the way to the engine compartment. No plastic or rubber lines!
New 100 micron and 10 micron filters included (these aren't cheap!)
Scan master installed in center vent.
Autometer pillar with fuel PSI guage and a boost guage. Also contains the autometer electronic fuel guage sending unit.
OBDI and OBDII computers and wiring harnesses. Right now OBDII is installed.
SPOHN torque arm
*buyer of the car can also have my cherry picker
The Engine:
383 stroker longblock brand new never fired
Heads have been decently ported but unfortunetly I do not have flow #'s.
Eagle cast crank
eagle forged rods
SRP forged pistons
LT4 hotcam kit
Aeromotive 13101 FPR - ($140 @ Summit)
TCI neutral balanced flexplate (engine is internally balanced) - ($75 @ Summit)
proform chrome valve covers ($210 @ Summit)
Lunati double roller timing chain already clearanced etc.. ($85 @ Summit)
ASP Billet damper / keyed hub ($150 dampner @ Summit / $100 for hub @ ASP)
Milodon oil pan for 383 with windage trey (~$200 @ VRE)
Mezeir HD elec water pump installed on housing. ($275 @ Summit)
Race ported LT1 intake powder coated red with blockoff plates installed.
Holley 58mm TB ($399.95 @ Summit)
36lb Lucas Injectors installed & 50lb Injectors not installed (~$300 for the 36ers @ ??)
Fuel rails have AN fittings welded on to accept the fuel lines in the camaro
Jet Hot LT (used in good shape) w/ new stage 8 locking bolts and reusable gaskets. ($300 @ private seller)
New optispark with pigtail ($309 @ Summit)
Over the valve cover wire loom kit with tailor cut to fit wires. (I only cut and installed one side so far) ($110 @ Thunder racing)
Moroso CAI (slightly used) ($100 @ Private seller)
Vortech polished elbow ($118 @ Summit)
NEW MAF
full set of TR-55 and TR6 plugs included. ($59 / ?)
*buyer of the engine will also recieve the engine stand it sits on.
Transmission:
Race built TH400 to handle 1000+HP (used 600 miles)
Reverse Manual Valve Body
Its got an aftermarket bellhousing installed as well. Can't recal the brand but its top notch. I will get the part # and look it up.
Electric external tranny cooler with fan and all braided lines.
Billet dip stick with braided line.
Vigilante 3300 stall
Custom steel 3" driveshaft to fit stock 10bolt with the TH400
B&M ratchet shifter
Nitrous:
I have a nitrous system I would like $450 for. It includes NX bottle with custom graphite paint job, NX purge, NOS bottle warmer, console switch panel for arming, MSD window switch, NX shark nozzle, all wires and lines required for installation. I paid $650 for this used but he guy claimed it was a $1100 kit. I will take pics if interested.
So heres the deal. I would like to sell the engine as one, tranny as one, and car as one. I don't want to split apart anything listed under those three categories. $6000 takes everything, I have double that invested.
If bought seperately...
car - $1500 firm (this car is beautiful!)
Engine $3750 OBO
Trans - $1500 OBO
Nitrous - $450 OBO
The best deal is the engine; the extra parts add up to over $2900 without even counting the engine, rods, crank, complete hotcam hit, heads, custom intake and fuel rails, etc.. I am selling this for half of what it costed!!!!
PM me or email me at dr1ft0r@yahoo.com. I can give my cell # to anyone interested, just ask
ENGINE:
Before I bought all the extra stuff
After some stuff
oil pan and engine mounts / jet hot headers
extra stuff
Last edited by LenT1; Sep 1, 2008 at 08:01 PM.
Thread Starter
Registered User
Joined: Feb 2005
Posts: 610
MORE PICS:
aeromotive a1000 fuel pump regulator and 100 micron filter / 10micron filter
new MAF
head ports
th400 pics
trans cooler
vig 3300 stall
where i plugged the water pump DS for the electric water pump
aeromotive a1000 fuel pump regulator and 100 micron filter / 10micron filter
new MAF
head ports
th400 pics
trans cooler
vig 3300 stall
where i plugged the water pump DS for the electric water pump
Last edited by LenT1; Sep 1, 2008 at 05:42 PM.
Registered User
Joined: May 2007
Posts: 852
From: Apopka FL
can I get some pics of the roller to mavericksis@yahoo.com please?
Registered User
Joined: Jan 2008
Posts: 1,900
From: warren,michigan
pics of the car to my1996z28@aol.com please
also what do you think shipping the car would cost to 48089?
also what do you think shipping the car would cost to 48089?
Registered User
Joined: Feb 2003
Posts: 715
From: Martin Mi
Detailed pics of roller to prorac1@chartermi.net Thanks Eric L
Thread Starter
Registered User
Joined: Feb 2005
Posts: 610
Pics finally added. Car needs a bath and a vacuum bad but it is very clean and a very beautiful car. If you want any specific pics of anything or higher res let me know. These have all been saved way down to save space.
