Roller SBC S/B and other Hi/Po SBC/LT1 inturnals
Thread Starter
Registered User
Joined: Aug 2002
Posts: 729
From: Scottsdale AZ
Roller 355 SBC S/B, solid roller parts, SBC/LT1 inturnals
I have a bunch of SBC/LT1 parts for sale
I have a set of used SRP forged pistons; j/e rings and pins less then 200 miles on them.
P/n srp-138086 and a matching set of j/e rings. These were in a motor that ate a cam there are pock marks on the side of the skirts. Nothing that would affect the motors performance, only the esthetics of the piston. I can and will provide pictures. I have seen people trying to sell far worse for more.
Specs: 4.040 bore 5/16th top 5/16th second and 3/16th oil. Pressed or floating pin and a 6.0 inch rod with a 3.48in stroke.
$300.00 Shipped OBO. New = $460 (pistons) $140 (rings) from summit.
I have a set of solid roller lifters – by comp cams- minus one lifter and cross bar also a matching set of pushrods-by comp cams- minus one. Less then 200 miles
Specs: fit standerd lifter bore sbc/lt1 all rollers are fine. Not sure of the part numbers on these. But looked at prices and its about 40 bucks average for a lifter and cross-bar and 10 for a pushrod form comp. A new set of bottom barrel S/R lifters is $350 not including push rods.
I will do $250 shipped OBO for lifters and pushrods. This set was like 500 new a few years ago.
I have a complete Roller Sbc short block either assmeled or un.
Its an 87-99 4-bolt main roller block that’s .040 Has been vated, line honed and magnafluxed. It has a balanced rotating assembly including a ZZ4 steel crank that’s 20/20 under. Matching Clevite 77 bearing, p/n cb-663-p-20 (rod) ms-909-p-20(main) and cam bearings. Rods are eagle SIR I beams in 6.0 inch form with pressed pins, P/N esp-6000bplw attached are SRP 4.040 11cc dome pistons pn.srp-140679 with matching J/E pro seal rings pn.0532-J100F8-40305. melling HV pump and bolt on pick up for the deep sump pan. TCI, SFI flex plate and SFI balancer. All machine work done by B & B Machine In Mesa AZ (have receipt’s) There’s a lot in this
I can assemble this or you can. It’s your choice?? Stating at $1750 OBO I can strap this to a pallet to ship.
Buyers’ pay all shipping charges (except where noted) and a 2.9999% handling Fee for PayPal.
I would like to sell this locally but who ever wants it wants it. Pictures can be e-mailed just lmk. If you are local send me a p.m. and I will shoot you my number so you can come look at this.
Eric
I have a set of used SRP forged pistons; j/e rings and pins less then 200 miles on them.
P/n srp-138086 and a matching set of j/e rings. These were in a motor that ate a cam there are pock marks on the side of the skirts. Nothing that would affect the motors performance, only the esthetics of the piston. I can and will provide pictures. I have seen people trying to sell far worse for more.
Specs: 4.040 bore 5/16th top 5/16th second and 3/16th oil. Pressed or floating pin and a 6.0 inch rod with a 3.48in stroke.
$300.00 Shipped OBO. New = $460 (pistons) $140 (rings) from summit.
I have a set of solid roller lifters – by comp cams- minus one lifter and cross bar also a matching set of pushrods-by comp cams- minus one. Less then 200 miles
Specs: fit standerd lifter bore sbc/lt1 all rollers are fine. Not sure of the part numbers on these. But looked at prices and its about 40 bucks average for a lifter and cross-bar and 10 for a pushrod form comp. A new set of bottom barrel S/R lifters is $350 not including push rods.
I will do $250 shipped OBO for lifters and pushrods. This set was like 500 new a few years ago.
I have a complete Roller Sbc short block either assmeled or un.
Its an 87-99 4-bolt main roller block that’s .040 Has been vated, line honed and magnafluxed. It has a balanced rotating assembly including a ZZ4 steel crank that’s 20/20 under. Matching Clevite 77 bearing, p/n cb-663-p-20 (rod) ms-909-p-20(main) and cam bearings. Rods are eagle SIR I beams in 6.0 inch form with pressed pins, P/N esp-6000bplw attached are SRP 4.040 11cc dome pistons pn.srp-140679 with matching J/E pro seal rings pn.0532-J100F8-40305. melling HV pump and bolt on pick up for the deep sump pan. TCI, SFI flex plate and SFI balancer. All machine work done by B & B Machine In Mesa AZ (have receipt’s) There’s a lot in this
I can assemble this or you can. It’s your choice?? Stating at $1750 OBO I can strap this to a pallet to ship.
Buyers’ pay all shipping charges (except where noted) and a 2.9999% handling Fee for PayPal.
I would like to sell this locally but who ever wants it wants it. Pictures can be e-mailed just lmk. If you are local send me a p.m. and I will shoot you my number so you can come look at this.
Eric
Last edited by faded93bird; Dec 31, 2009 at 06:02 PM.
Thread Starter
Registered User
Joined: Aug 2002
Posts: 729
From: Scottsdale AZ
I forgot to add that the compression ratio with the dome pistons will be.
12.5-14.7 depending on what cc the chambers in your heads and what gaskets you use.
Also this bottom end will be good for 600 hp
Eric
12.5-14.7 depending on what cc the chambers in your heads and what gaskets you use.
Also this bottom end will be good for 600 hp
Eric
Thread
Thread Starter
Forum
Replies
Last Post