I've decided that everything has to go. Can't afford the hobby any longer.

SOLD CPT Pro-Race 4L60E SOLD
SOLD Beautiful Vigilantee Torque converter SOLD
SOLD Moser 12 Bolt rear endStrange 1702 chromolly Drive Shaft SOLD
Spohn adjustable panhard bar SOLD.
Spohn Solid 25mm rear sway barSOLD
"Hot Parts" standard rear control arms SOLD
1LE Elbow SOLD

Pics to come:

M/T skinnies mounted on forged telstar rims. Lots of tread left. Over $600 retail. $300 plus shipping/paypal fee

Holley 58mm Throttlebody - perfect mint condition with seal. $218 shipped fees included.

Delphi 38lb fuel injectors - set of 9 perfect less than 1000 miles on them. For detailed description see this link: http://www.racetronix.biz/itemdesc.a...113798&eq=&Tp=.$210 shipped fees included.

Complete Delteq ignition system minus wires. 3000 miles on it. Works perfectly. Drove my car with it on 150 miles just prior to braking it down. Retails over $600. Priced to go $230 shipped w/paypal fees included

LT1 Fuel Rail - $50 shipped

Eibach Pro 1"-1.5" lowering springs fronts have KYB struts included - about 4000 miles on them. $200 shipped


C5 Chrome wheels w/Nitto 555 tires mounted - perfect condition. Fronts are 17"x8.5" and rears are 17" x 9.5" to accomidate the lowering springs listed above. $800 plus shipping and paypal fees

This is one of the front tires that was out of toe. If aligned correctly it has good tire tread left on the other side.

This is what the other three tires look like as far as tread wear is concerned. Basically new.


M/T DR with 80% tread left mounted on salad shooters. $150 you handle shipping




LT1 MAF - ported descreened w/red housings on both ends. $60 shipped



RK Sport SS spoiler for 93-97 Camaro. 98+ style design. Beautiful condition. Purchased off of this board from another member. I can ship it via Greyhound for $300 shipped.


383 stroker, P/P heads flow 272cfm in. .560", LE ported Red Intake, CC306 Long block. Fully forged bottom end w/H-beam rods. With a male order tune I managed 92mph in 1/8 mi and 1.58 60". Great street/strip set up with tons of down low torque. All forged internals ready for lots of nitrous. I have not shot any nitrous to it yet though. I've put $6800 into this motor. I will post pics of all work done by the machine shop and parts used as soon as I get the chance. I'm looking to get at least $3000 for complete Long block buyer handles all shipping. If you live close enough we may can work something out on meeting half way. Interested parties IM for details.

Engine as it sits now:


All prices are firm and subject to closing with no notice via local sales. If paying via Paypal you must add the 3% fee. Will accept money order or personal check. All checks must clear prior to shipping. Buy with confidence as I've sold things here for quiet a while and been around these boards for a good amount of years. More items will be added as I get them ready to be sold.

 

SOLD Moroso LT1 specific 5.5 qt. Deep Oil pan. Comes with HV pump and pickup welded to the pump. Also comes with the steel rod for the pump. For details on the pan see this link: http://www.moroso.com/catalog/catego...?CatCode=17001

The hole you see in the top view has been made larger to fit the larger pickup assembly. For picks IM me your cell number and I'll send you pics through the phone. SOLD

 

how's the oil pan clearance on the k? does it sit much lower than the stocker?

 

Not sure as I haven't installed it. It's ment for the LT1 so I wouldn't imagine clearance would be much of an issue compared to any other pan. Some other folks with this pan may have some input though.

 

Hi, I have that oil pan on my 95 Z28, it works fine. I have Edelbrock headers and y-pipe. It was a little close, I just loosened the bolts and moved the pipe and then tightened them up. My car is lowered 2". Just letting you know.Ray

 

More parts added. Pics to be added tonight 6-19-10.

 

I would need the driveshaft you're selling or else a new fitting on mine to replace my factory rear end with this one, right?

 

^Yes that is correct. Due to the larger 1350 joint.

Hey guys just remember everything is up for grabs off of this car(if your looking for something ask me and I'll let yo know if I have it). I go on vacation tuesday June 29 through July 5th so my next shipping windows are Monday June 29th for stuff already taken off of the car or that can be quickly taken off then July 6th.

 

PM sent for oil pan.

Sent from my Droid using Tapatalk

 

PM sent about torque arm Thanks muddz28

 

All Items as of today have been shipped out if you purchased from me. Post has been updated after pulling a bunch of stuff today and pics added. Next available ship day is going to be around July 6th. Thanks guys for your interest.

 

what exhaust was on the car?

 

A true dual set up that was custom made for the spohn torque arm and Hooker LT Headers that I had with 3" pipe and two 2.5" stainles magnaflow mufflers and turn downs prior to the rear axle. It was absolutely awsome. The best hot rod exhaust set up I've ever heard. I have a pic of it for ya too.

 

You have a good picture of the 1LE Elbow? If it's in as good a shape as you say, I'll take it.

 

When u get back if u you could pm me Bout your exhAust very interested in the full set up. Thanks have a great vacation!