Moser 33 spline center section /3.73 gears with pics
#1
Moser 33 spline center section /3.73 gears with pics
What I have here is an Eaton Center section out of a 12-bolt, newly rebuilt with the carbon fiber disks in it to replace the steel friction disks that were in it and problematic. The rear and the gears have about 15,000 miles on them. This unit has the drag clutch springs in it (800lb versions instead of the street 400lb versions). It comes with the Moser (or whoever supplies Moser with their gears) 3.73's. After being rebuilt (by Moser) the unit has around 5-800 miles on it before I parked the car and tore it all apart. I bought a spool and cannot use the gears since this carrier is a 3-series and the spool is a 4. Looking to get $425 for the package, and I will pay shipping (excpet outside the US, and it will be ground, with insurance optional that you will be responsible for). Here are some pictures:
Last edited by drivefast4fun; 01-03-2006 at 09:59 PM.
#2
Re: Moser 33 spline center section /3.73 gears with pics
how about $400.00? all you would need to do is buy a housing with 9" ends on it, some axles and an install kit. Figure a housing is $919 with ends, or you can get a housing with axles and bearings for $1295, you have yourself a full 12 bolt for about $1700. The full package is over $2000 from Moser.
As taken from the Moser site:
12 Bolt - F-Body and Coil Spring Rear
12 Bolt Housing Only $919
(Includes 12 Bolt Housing with brackets Installed and new housing ends)
12 Bolt Housing & Axle Package $1295
(Includes 12 Bolt Housing with brackets, M/E Custom Alloy Axles, new housing ends, wheel bearings, wheel studs, retainer plates)
Complete 12 Bolt w/Full Spool $2009
(less brakes) Torque Arm Cars & Coil Spring Rears w/ears Includes 12 Bolt Housing, M/E Custom Alloy Axles, wheel bearings, wheel studs, retainer plates, full spool (30 or 33 spline), Pro Street gears, 1350 series pinion yoke, chrome cover and assembly
* Add for Performance Rearend Cover $135
* Add for 4 channel ABS setup $100
* Add for new exciter rings $75
Installed on axles for 4 channel setup
* 3 channel ABS not available
* Subtract for 1310 series pinion yoke -$35
Complete 12 Bolt w/Limited Slip (less brakes) $2249
Torque Arm Cars & coil Spring Rears w/Rears
Includes 12 Bolt Housing, M/E Custom Alloy Axles, wheel bearings, wheel studs, retainer plates, Eaton Posi or Truetrac Limited Slip(30 spline), Pro Street gears, 1350 series pinion yoke, chrome cover and assembly
* Add for 33 spline Eaton Posi-Unit $100
* Add for 33 spline Truetrac Limited Slip $65
* Add for Performace Rearend Cover $135
* Add for 3 channel ABS setup $100
* Add for 4 channel ABS setup $100
* Add for new exciter rings $75
installed on axles for 4 channel setup
* Subtract for 1310 series pinion yoke -$35
If you look at just the last set up it is $2249, then an extra $100 for this set up, so you could save yourself a few hundred dollars. This unit is fully rebuildable, and has been a VERY short time ago with the upgraded friction rings.
As taken from the Moser site:
12 Bolt - F-Body and Coil Spring Rear
12 Bolt Housing Only $919
(Includes 12 Bolt Housing with brackets Installed and new housing ends)
12 Bolt Housing & Axle Package $1295
(Includes 12 Bolt Housing with brackets, M/E Custom Alloy Axles, new housing ends, wheel bearings, wheel studs, retainer plates)
Complete 12 Bolt w/Full Spool $2009
(less brakes) Torque Arm Cars & Coil Spring Rears w/ears Includes 12 Bolt Housing, M/E Custom Alloy Axles, wheel bearings, wheel studs, retainer plates, full spool (30 or 33 spline), Pro Street gears, 1350 series pinion yoke, chrome cover and assembly
* Add for Performance Rearend Cover $135
* Add for 4 channel ABS setup $100
* Add for new exciter rings $75
Installed on axles for 4 channel setup
* 3 channel ABS not available
* Subtract for 1310 series pinion yoke -$35
Complete 12 Bolt w/Limited Slip (less brakes) $2249
Torque Arm Cars & coil Spring Rears w/Rears
Includes 12 Bolt Housing, M/E Custom Alloy Axles, wheel bearings, wheel studs, retainer plates, Eaton Posi or Truetrac Limited Slip(30 spline), Pro Street gears, 1350 series pinion yoke, chrome cover and assembly
* Add for 33 spline Eaton Posi-Unit $100
* Add for 33 spline Truetrac Limited Slip $65
* Add for Performace Rearend Cover $135
* Add for 3 channel ABS setup $100
* Add for 4 channel ABS setup $100
* Add for new exciter rings $75
installed on axles for 4 channel setup
* Subtract for 1310 series pinion yoke -$35
If you look at just the last set up it is $2249, then an extra $100 for this set up, so you could save yourself a few hundred dollars. This unit is fully rebuildable, and has been a VERY short time ago with the upgraded friction rings.
Thread
Thread Starter
Forum
Replies
Last Post
dbusch22
Forced Induction
6
10-31-2016 11:09 AM