ALL PRICES ARE OBO AND DO NOT INCLUDE SHIPPING

Stock stuff:
-Complete AIR system $25
-Stock LT1 Camshaft $50
http://good-times.webshots.com/photo...97142729qDrgKV
http://good-times.webshots.com/photo...97142729jtdWzS
http://good-times.webshots.com/photo...97142729EcARGf
-Stock LT1 tensioner $5
-AIR pump bracket MAKE OFFER
-I have no idea what these are but if you do and want them they're yours
http://good-times.webshots.com/photo...97142729pBAKFe
-50k mile A/C motor $25
http://good-times.webshots.com/photo...97142729ZikJZS
http://good-times.webshots.com/photo...97142729EjykLP
-Stock valve covers $40
-Stock 50k mile lifters $20
-Stock 50k mile shortblock(block, crank, rods, pistons, oil pan) $200

Modified stock stuff:
-95+ timing chain cover with crank sensor, clearanced for double-roller timing chain, water pump hole blocked off $60
http://good-times.webshots.com/photo...97142729OhTXEt
http://good-times.webshots.com/photo...97142729cIzrRf
http://good-times.webshots.com/photo...97142729TeHxqj
http://good-times.webshots.com/photo...97142729dXdunT
-Stock valve covers clearanced for 1.6 roller rockers with like-new(1-hour runtime) gaskets $50
http://good-times.webshots.com/photo...97142729eMBkIn
http://good-times.webshots.com/photo...97142729WGNoSo
http://good-times.webshots.com/photo...97142729SOZJhy
http://good-times.webshots.com/photo...97142729jntINj
http://good-times.webshots.com/photo...97142729wQhkbC
http://good-times.webshots.com/photo...97142729atrpqb
-Electric water pump housing with heater and oil cooler hoses blocked off, like-new(1-hour runtime) 180* t-stat, and like-new(1-hour runtime) coolant temp-sensor $50
http://good-times.webshots.com/photo...97142729YvwgUP
http://good-times.webshots.com/photo...97142729PCwAiO
http://good-times.webshots.com/photo...97142729KkysgR
http://good-times.webshots.com/photo...97142729lHqFhw
-Boxed stock lcas $10
http://good-times.webshots.com/photo...97142729kDCVLv
-(2) Stock 48mm throttle bodies with airfoil installed(only have pics of one but both look the same) $50 EACH
http://good-times.webshots.com/photo...97142729QFScRm
http://good-times.webshots.com/photo...97142729cGZsak
-Stock intake manifold w/ fuel rail and EGR blockoff plates installed$110

Aftermarket stuff:
-30# SVO yellow-top injectors $200
http://good-times.webshots.com/photo...97142729msKJDl
-K-motion K800 springs w/ titanium retainers and 10* locks(10k miles) $200
http://good-times.webshots.com/photo...97142729aYgHdf
http://good-times.webshots.com/photo...97142729xXjWEw
http://good-times.webshots.com/photo...97142729yhEsBZ
http://good-times.webshots.com/photo...97142729EXUMiP
-Stock heads(media blasted with valves cut and lapped) $210
-918 “beehive” springs with upper and lower retainers and locks(Broken-in only never run on street) $200
Pics of heads and valvetrain(click "next" to scroll through all pics
-Custom grind cam 22x/23x, .56x/.56x w/ 1.6 rockers, 110 lsa $250
(Cam was designed to make the same power as the "CC306" but at a lower rpm)

 

the injectors look like accel? do you any boxs or anything showing they are svo? i might be intrested for about 150?

 

I purchased them used as ford injectors and after tuning the pcm that way the car ran properly...I don't know where or how much it costs to have them flow-tested but i can possibly have it done in order to verify what they are...any idea what it would cost to have it done?

 

pictures of heads added

 

rockers and pushrods sold. Opti added.

 

Can you do $35 shipped on the bracket I dont need the tensioner.
Chicago area

 

pm sent

 

ttt...im only leaving this stuff up for a week or so before it all goes to ebay...

 

ttt...7 days till ebay

 

6 days till ebay...i hit a deer and need the $$$ bad

 

5 days till ebay

 

4 days till ebay

 

Will you sell just the heads without any of the valvetrain? If so how much, casting number?

 

I believe the casting number is 5214 and yes I will seperate...any interest in the valvetrain and not the heads?

 

were the heads actually ported any? or just valvetrain work? will you do 50 shipped for the cloyes? email me at roynaidu@shaw.ca