Pictures of everything below can be seen here:

http://home.comcast.net/~mhansel658/parts.htm

Pulled the engine to make room for the stroker. All of these parts, with the exception of the shortblock, have less than 10k Miles and are in excellent shape.

Ported and Polished LT1 Assembled Heads- Heads were sold to me as ported by Jordon Musser, I talked with him about them and he couldn't verify for sure if he did them without me sending them to him, which I never did. At any rate they have extensive intake, exhaust and bowl work. I ran a 12.0 with these heads in a full weight manual car, (dropped .3 tenths of my previous best E.T just by bolting these on). Heads have a fresh performance valve job and "skim" milling just to ensure flatness of surface. 58cc Combustion Chambers, ARP 7/16" Studs, GMPP Guide Plates, 2.00/1.56 Manley Race Flow Valves, New 99893 Crane Springs, Comp Cams 611 10* Locks, CC 740 Retainers, and CC 4770 Seats. Heads have less than 3k miles with these components.

Here is a link to the thread where I originally purchased the heads:

http://web.camaross.com/forums/showt...ghlight=Musser

-Heads are SOLD !!

Stock Block (2 Bolt Main) Looks good, no signs of excessive wear - (SOLD)

Comp Cams Hardened Push Rods (Recommended for use with guide Plates)
- $50.00 (Sold)

Spec Stage 2 Clutch/Pressure Plate/TO Bearing - Clutch has plenty of meat left on it. Never had a single problem with this clutch - Sold

Stock Rotating Assembly - No signs of excessive wear, bearings looked good upon teardown - (SOLD)

Stock LT1 Flywheel - Sold

Stock 93 LT1 Intake (Painted Orange) - Sold

Another Stock 93 LT1 Intake missing Oil Deflector - Sold

LT1 93 Fuel Rail - $50.00

30Lb SVO Injectors Excellent Shape - Sold

Crane Fireball Coil - $35.00

ICM Module - $25.00

Stock Oil Pan (SOLD) - Includes stock baffles/windage tray, you can even have the Oil Pump and Pickup if you want.

Stock K Member and A Arms. Arms have fresh ball joints, (upper and lower), (15k) and Energy Suspension poly bushings - Sold

MSD 8.5 Wires Cut to fit OVC Setup Good Shape You can have the OVC looms but I'm missing one, (Heat Sheilds in Picture are NOT Included) - (SOLD)

Koni Single Adjustable Front Shocks - Model 8241-1139, less than 10k on these. Great handling and Road Racing shock. SOLD with a set of 2 SLP Take off springs. (SOLD)

Rear Bilstein HD Strano Valved Shocks and stock rear springs - Good condition relatively low miles, less than 10k, bought the front and rear setup using Sam Strano's recommendation. - Sold

AC System - Compressor, barely used rebuilt AC Delco, lines, condensor, everything that I can pull off of the under the hood. Blew Ice Cold until I pulled it out. -(Sold)

All prices unless noted do NOT include shipping. I'll entertain reasonable offers . I've got a good record on this board, both selling and buying, I ship fast and accept PayPal, Money Order or Personal Check, (As long as you don't mind waiting for your check to clear). Best to contact me at the below email address.

mhansel658@comcast.net

 

pm sent on MSD wires

 

I got dibs on the pushrods... 7.2 right??? got any paperwork on them?? Just trying to keep a paper trail on the new motor...

 

Would those head work well on a 396 forged???? if so im interest on the heads.

 

I don't think I have any paperwork on the pushrods, but yes they are 7.2. Comp Cam hardened pushrods. I'll look for the receipt.

 

They'll work on a 396 provided your set up to use a 58cc chamber, but honestly stock ported castings wouldn't be my first choice for a 396.

 

Edit - Added Block, K-member and Oil Pan

 

I got dibs on the heads bro but just let me talk to my friends that doin my 396 stroked. He a LT1 pro, so if he says they'll work then I got them.

 

Sounds good, let me know. These really are a nice set of heads, a few other members on this board know my car, it was fast, and in the hands of someone who knew how to drag race, even faster.

Also added rear shocks and springs.

 

what about $100 for the ac system shipped to kissimmee fl 34741.....it working right ???thank you man

 

Can't go quite that low shipped. I'll do $150.00 shipped to Kissimee.

 

are you selling the thottle body? i would be interested in it. let me know
pricez28@hotmail.com

 

Sorry no. I'm keeping the TB.

 

Ill take the pushrods. I was hoping for a receipt but its cool. I can just print the info on them from their website.

 

how much for the konig wheels?