LT1 Engine Part Out -1997
Thread Starter
Registered User
Joined: Feb 2007
Posts: 293
LT1 Engine Part Out -1997
I'm in the process of swapping to an LQ4 and want to clear out the garage of the old engine parts. Many of them only have 1-2k on them as they were put in last March. PM me if you'd like more information. The engine block I prefer NOT TO SHIP. All parts are from a 97 WS6 and I accept paypal or cash in person. Prices do NOT include shipping.
ALL PICTURES HERE : For Sale Photos by 97TAWS6 | Photobucket
Ebay Speed Daddy Headers - Dented to fit around the steering shaft and come with Delphi O2 sensors that were put in last March. Sold
Brushed Aluminum valve covers. Needs Screws with countersink. I have some of them, but looks like someone ran off with a few. Sold
Comp Cams 1.6 SA Pro Mag Rockers - Made for stock stud and comes with the poly locks. Some have slight surface rust on the body from when I had the valve covers off last year for a week when it was really muggy out. Unknown Mileage on them. SOLD
Intake Manifold - Snapped fuel rail bolt and throttle cable bracket bolt, will need extraction. Painted High Temp Silver to look fresh cast. $50
CC Performance MSD OTVC wire set - Less than 2K on them, comes with coil wire. The mounting screws on the dividers are longer than stock because of the tall valve covers I used, tightened to hold and I cannot get them out as you can see in the pic. $95
KB .030+ Hyper Pistons and Eagle 6" Rods- Look about 6cc dish and rods have ARP bolts. Balanced. Slight scuffs on the skirts. $150
Stock Crank - Balanced to the rods above. Will need the crank snout either drilled and tapped for larger bolt, or timesert/helicoiled. Also, note the scuffs on the journals, will need to be turned/polished. $50 separate, or $25 if you buy the rods/pistons with it.
Melling HV Oil Pump - Comes with the oil pump drive, which has a steel coupler, not plastic. $20
LT1 Block punched .030 over. No spun mains, and some scuffs on the cylinder walls. Close pics of the worst one. WILL NOT SHIP. $150
ALL PICTURES HERE : For Sale Photos by 97TAWS6 | Photobucket
LT1 Starter - SOLD
LT1 Oil Pan - $40
LT1 Water Pump - $45
LT1 AC Compressor - $30
LT1 T56 Dust Cover - $15
97 M6 PCM Programmed my MadZ28 for LT1 with CC305, LT HEADERS, 1.6RR, Cats, 3.73 Gears and all emissions removed. $75
LT1 Kmember - $50
LT1 Throttlebody Noticed the screws for the TPS are jacked up and there is some type of glue that was holding an airfoil.. instead of a screw.- $25
ALL PICTURES HERE : For Sale Photos by 97TAWS6 | Photobucket
Ebay Speed Daddy Headers - Dented to fit around the steering shaft and come with Delphi O2 sensors that were put in last March. Sold
Brushed Aluminum valve covers. Needs Screws with countersink. I have some of them, but looks like someone ran off with a few. Sold
Comp Cams 1.6 SA Pro Mag Rockers - Made for stock stud and comes with the poly locks. Some have slight surface rust on the body from when I had the valve covers off last year for a week when it was really muggy out. Unknown Mileage on them. SOLD
Intake Manifold - Snapped fuel rail bolt and throttle cable bracket bolt, will need extraction. Painted High Temp Silver to look fresh cast. $50
CC Performance MSD OTVC wire set - Less than 2K on them, comes with coil wire. The mounting screws on the dividers are longer than stock because of the tall valve covers I used, tightened to hold and I cannot get them out as you can see in the pic. $95
KB .030+ Hyper Pistons and Eagle 6" Rods- Look about 6cc dish and rods have ARP bolts. Balanced. Slight scuffs on the skirts. $150
Stock Crank - Balanced to the rods above. Will need the crank snout either drilled and tapped for larger bolt, or timesert/helicoiled. Also, note the scuffs on the journals, will need to be turned/polished. $50 separate, or $25 if you buy the rods/pistons with it.
Melling HV Oil Pump - Comes with the oil pump drive, which has a steel coupler, not plastic. $20
LT1 Block punched .030 over. No spun mains, and some scuffs on the cylinder walls. Close pics of the worst one. WILL NOT SHIP. $150
ALL PICTURES HERE : For Sale Photos by 97TAWS6 | Photobucket
LT1 Starter - SOLD
LT1 Oil Pan - $40
LT1 Water Pump - $45
LT1 AC Compressor - $30
LT1 T56 Dust Cover - $15
97 M6 PCM Programmed my MadZ28 for LT1 with CC305, LT HEADERS, 1.6RR, Cats, 3.73 Gears and all emissions removed. $75
LT1 Kmember - $50
LT1 Throttlebody Noticed the screws for the TPS are jacked up and there is some type of glue that was holding an airfoil.. instead of a screw.- $25
Last edited by sandman2100; Oct 17, 2013 at 12:21 PM. Reason: Updated
Thread
Thread Starter
Forum
Replies
Last Post
oldschool
Parts For Sale
16
Feb 9, 2016 09:21 PM