LT1 & 6-speed Engine Package
LT1 & 6-speed T56 Engine Package
After 3 years it is time for me to move on to another project. I am selling the entire LT1 engine/tranny package from my 86 IROC. The engine is in perfect running condition and will remain in the car until it is sold so it can be run and driven. Below are all the details. Pictures and Dyno charts are available upon request and in my user profile album.
Engine Details
94 LT1 and T56 6-speed
350 Cubic Inches
Rebuilt in May 2007
Approximately 5,000 miles on rebuild
Stock Computer
Stock Aluminum Heads
Stock Crank, Rods and Pistons
New bearings
2-bolt mains w/ ARP studs
New Oil Pump, Alternator and Water Pump
Stock Timing Chain
LT-4 Hot Cam (.525 int/.525 exht with 1.6 rockers)
GM Performance 1.6 Roller Rockers (Crane)
GM Performance Valve Springs, Retainers and Keepers
GM Performance Hydraulic Lifters
New GM Opti-spark
New Packard wires and AC plugs
Edelbrock Shorty Headers
Tuned with CATS (302 RWHP / 325 RWTQ)
Transmission Details
6-Speed Manual w/Ram Clutch
Misc Info
Engine is currently wired to fit in a 1986 Z-28 Camaro. Most of the stock connectors were retained so harness could still be used in other applications.
Transmission cross member can be supplied for 3rd Gen Camaro if required.
Contact
Asking $3,500 OBO for everything (engine, transmission, harness, computer and all sensors)
Call at 706-495-0966 or email at furman100@comcast.net
Engine Details
94 LT1 and T56 6-speed
350 Cubic Inches
Rebuilt in May 2007
Approximately 5,000 miles on rebuild
Stock Computer
Stock Aluminum Heads
Stock Crank, Rods and Pistons
New bearings
2-bolt mains w/ ARP studs
New Oil Pump, Alternator and Water Pump
Stock Timing Chain
LT-4 Hot Cam (.525 int/.525 exht with 1.6 rockers)
GM Performance 1.6 Roller Rockers (Crane)
GM Performance Valve Springs, Retainers and Keepers
GM Performance Hydraulic Lifters
New GM Opti-spark
New Packard wires and AC plugs
Edelbrock Shorty Headers
Tuned with CATS (302 RWHP / 325 RWTQ)
Transmission Details
6-Speed Manual w/Ram Clutch
Misc Info
Engine is currently wired to fit in a 1986 Z-28 Camaro. Most of the stock connectors were retained so harness could still be used in other applications.
Transmission cross member can be supplied for 3rd Gen Camaro if required.
Contact
Asking $3,500 OBO for everything (engine, transmission, harness, computer and all sensors)
Call at 706-495-0966 or email at furman100@comcast.net
Last edited by DakotaR6; May 7, 2010 at 08:31 AM.
This sounds like a good deal, I am currently doing a rebuild on my TA, it is going to cost me around the same price as your setup. I would not want to make a lowball offer on such a good setup, but I would have to in order to swing it. This is a killer deal, good luck!
Charlie
Charlie
Sorry about that late response I just got the 2 last post and I know it is a month later. I still have the engine and it is negotiable. Make me an offer of what you can afford! Just send me a PM.
This sounds like a good deal, I am currently doing a rebuild on my TA, it is going to cost me around the same price as your setup. I would not want to make a lowball offer on such a good setup, but I would have to in order to swing it. This is a killer deal, good luck!
Charlie
Charlie
Package is up on Ebay now with a Buy it Now or Best offer if there is any interest.
http://cgi.ebay.com/ebaymotors/LT-1-...Q5fAccessories
http://cgi.ebay.com/ebaymotors/LT-1-...Q5fAccessories
Thread
Thread Starter
Forum
Replies
Last Post
F'n1996Z28SS
Cars For Sale
8
Aug 23, 2023 11:19 PM
oldschool
Parts For Sale
16
Feb 9, 2016 09:21 PM
TheGreenZ28
Exhaust System
0
Dec 6, 2014 10:23 PM
chevroletfreak
LT1 Based Engine Tech
202
Jul 4, 2005 05:00 PM



