kmook's 2005 Blowout ;)
Thread Starter
Advanced Tech Moderator
Joined: Aug 2001
Posts: 2,262
From: Nashville
kmook's 2005 Blowout ;)
Everything is brand new never installed unless noted otherwise. And everything is for the LT1. (I prefer paypal)
-LT1 Heads ported by Blackstone (http://watsonracingengineering.com). 2.05" intake 1.60 exhaust valves (new seats), These are LJ's old heads that he went 9.94 at 139+ in a 3750lb car! $1900 (Cost over $3000) (Look at the low/mid lift #s!)
Flowed by two seperate companies-
Blackstone---|---BRE
100- 74/64------90/(no pipe so no #s)
200- 147/118---153/
300- 203/167---207/
400- 249/197---253/
500- 269/214---275/
600- 284/225---275/
---
-ARP Head bolts (Sold)
-Delteq complete ignition system (Mounts for the raditor shroud or my custom intake mount) - (Sold)
-LT4 Composite Valve covers (complete) with mba silver trim kit- (Sold)
-AS&M Monoblade (Sold)
-Cloyes True Double Roller Adjustable Timing Chain Set (Sold)
-7psi radiator cap (to run Evans NPG+ Coolant) - (Sold)
-Moroso solid engine mounts- (Sold)
-Combination Motorsports LT1 Camshaft Swap Gasket Package
Intake Gaskets, Fel-Pro Timing Cover Gasket, Opti Seal, Crank Seal, Water Pump Drive Seal (Sold)
-Comp Cams "R" Hydraulic Roller Lifters (Sold)
-Comp Cams Hi-Tech Stainless Non-Self-Aligning Roller Rocker Arms, 7/16" stud, 1.6 Ratio- (Sold)
-BRE ProRam Intake Designed to produce substancial hp and trq gains throughout the rpm range. Powdercoated black, and comes with
the fuel rails and lines to mate to stock lt1 fuel lines installed. (Sold)
-Trickflow elbow (black)- (Sold)
-K&N RE-0860 Filter (Flows 1357cfm) 4" Inlet- (Sold)
-Breslin Intake Manifold bolts- (Sold)
-Mr. Gasket head gaskets .026" #5716 - (Sold)
-Granatelli Maf (Sold)
-AP Engineering 355 LT1 Shortblock. Complete New shortblock with no core charge/exchange, this is at AP Engineering waiting to be shipped. 11:1 c/r with stock head chamber size, polished and magnafluxed stock crank, diamond forged pistons, diamond 4130 choremoly wrist pins, diamond proselect rings, eagle H beam rods, federal mogul 152M main bearings, clevite CB663H Connecting rod bearings, ARP Main Studs, Splayed 4-Bolt Billet Main Caps, Blueprinted, fully balanced and assembled. (Sold)
-Breslin Header bolts- (Sold)
-LT1 Heads ported by Blackstone (http://watsonracingengineering.com). 2.05" intake 1.60 exhaust valves (new seats), These are LJ's old heads that he went 9.94 at 139+ in a 3750lb car! $1900 (Cost over $3000) (Look at the low/mid lift #s!)
Flowed by two seperate companies-
Blackstone---|---BRE
100- 74/64------90/(no pipe so no #s)
200- 147/118---153/
300- 203/167---207/
400- 249/197---253/
500- 269/214---275/
600- 284/225---275/
---
-ARP Head bolts (Sold)
-Delteq complete ignition system (Mounts for the raditor shroud or my custom intake mount) - (Sold)
-LT4 Composite Valve covers (complete) with mba silver trim kit- (Sold)
-AS&M Monoblade (Sold)
-Cloyes True Double Roller Adjustable Timing Chain Set (Sold)
-7psi radiator cap (to run Evans NPG+ Coolant) - (Sold)
-Moroso solid engine mounts- (Sold)
-Combination Motorsports LT1 Camshaft Swap Gasket Package
Intake Gaskets, Fel-Pro Timing Cover Gasket, Opti Seal, Crank Seal, Water Pump Drive Seal (Sold)
-Comp Cams "R" Hydraulic Roller Lifters (Sold)
-Comp Cams Hi-Tech Stainless Non-Self-Aligning Roller Rocker Arms, 7/16" stud, 1.6 Ratio- (Sold)
-BRE ProRam Intake Designed to produce substancial hp and trq gains throughout the rpm range. Powdercoated black, and comes with
the fuel rails and lines to mate to stock lt1 fuel lines installed. (Sold)
-Trickflow elbow (black)- (Sold)
-K&N RE-0860 Filter (Flows 1357cfm) 4" Inlet- (Sold)
-Breslin Intake Manifold bolts- (Sold)
-Mr. Gasket head gaskets .026" #5716 - (Sold)
-Granatelli Maf (Sold)
-AP Engineering 355 LT1 Shortblock. Complete New shortblock with no core charge/exchange, this is at AP Engineering waiting to be shipped. 11:1 c/r with stock head chamber size, polished and magnafluxed stock crank, diamond forged pistons, diamond 4130 choremoly wrist pins, diamond proselect rings, eagle H beam rods, federal mogul 152M main bearings, clevite CB663H Connecting rod bearings, ARP Main Studs, Splayed 4-Bolt Billet Main Caps, Blueprinted, fully balanced and assembled. (Sold)
-Breslin Header bolts- (Sold)
Last edited by kmook; Jan 31, 2005 at 08:41 PM.
Thread Starter
Advanced Tech Moderator
Joined: Aug 2001
Posts: 2,262
From: Nashville
Re: kmook's 2005 Blowout ;)
Originally Posted by jssws-6
$65 shipped if so I'll send money out tonight
Thread Starter
Advanced Tech Moderator
Joined: Aug 2001
Posts: 2,262
From: Nashville
Re: kmook's 2005 Blowout ;)
Originally Posted by ATEBYASNAKE
Got any pics of the Monoblade?
Thread Starter
Advanced Tech Moderator
Joined: Aug 2001
Posts: 2,262
From: Nashville
Re: kmook's 2005 Blowout ;)
Originally Posted by Zigroid
those LT4 valve covers are looking mighty tempting... any pics?
Thread Starter
Advanced Tech Moderator
Joined: Aug 2001
Posts: 2,262
From: Nashville
Re: kmook's 2005 Blowout ;)
Originally Posted by PipesTA
I'll take the LT4 covers. Would you take 175 shipped. Can paypal whenever. LMK
Thread Starter
Advanced Tech Moderator
Joined: Aug 2001
Posts: 2,262
From: Nashville
Re: kmook's 2005 Blowout ;)
Originally Posted by Zigroid
and how good of shape is the delteq in?
