Interest in complete Forged 381?
Thread Starter
Registered User
Joined: Oct 2002
Posts: 1,639
From: Toledo, OH
Interest in complete or separated Forged 381?
Looks like its getting parted out now, so email me with interest and Ill give you prices.
I am currently in the process of tearing it down and checking/reassembling/blueprinting the engine.
has about 1000 miles on it, ~600 easy clutch breakin miles
-Fully machined block
--4bolt splayed caps
--align bore/hone
--bore/hone .020 with torque plate
--balanced internally
--Decked to .005
--core plugs/oil passage flush/cam bearings
-Eagle 4340 3.75" Crank ground .010 on rods/mains to straight
-Eagle Hbeam 4340 6" rods w/ARP L19 bolts
-SRP forged pistons 16cc dish (~11.00:1 SCR)
-JE plasma moly coated ductile iron rings
-Clevite H bearings
-ARP main studs
-Eagle billet steel middle caps/Program front cap
-Melling HV oil pump
-Stefs fabricated aluminum oil pan w/stroker notches/baffles/and teflon windage tray
-ATI steel balancer
-SLP billet steel flywheel (must be purchased, balanced with rotating assy)
-Spec Stage 3 Ceramic clutch
-Joe overton ground cam 242/250 @50 .558/.558
-Rollmaster billet timing set
-Comp R lifters
-trick flow 7.150" pushrods .080 wall
-Comp Promagnum rockers
-Comp 977 springs
-comp spring hardware 4771/611/740
-Ferrea 2.0"/1.56" 6000 series stainless valves
-Lloyd Elliot ported LT1 castings (flow sheet upon request)
-Lloyd Elliot ported LT1 intake (provision for 58mm)
-Accell 30# injectors
-CSI electric H2O pump
-Rebuilt Vented '96 Opti (if you have a newer opti I wont install the WP so you can install your own)
Also for sale
BMR kmember $325
C5 brake conversion w/wilwood pads $600
I have pictures of everything on my page, but no HTML for it, so ask me and ill link you directly to the picture of what you want
I am currently in the process of tearing it down and checking/reassembling/blueprinting the engine.
has about 1000 miles on it, ~600 easy clutch breakin miles
-Fully machined block
--4bolt splayed caps
--align bore/hone
--bore/hone .020 with torque plate
--balanced internally
--Decked to .005
--core plugs/oil passage flush/cam bearings
-Eagle 4340 3.75" Crank ground .010 on rods/mains to straight
-Eagle Hbeam 4340 6" rods w/ARP L19 bolts
-SRP forged pistons 16cc dish (~11.00:1 SCR)
-JE plasma moly coated ductile iron rings
-Clevite H bearings
-ARP main studs
-Eagle billet steel middle caps/Program front cap
-Melling HV oil pump
-Stefs fabricated aluminum oil pan w/stroker notches/baffles/and teflon windage tray
-ATI steel balancer
-SLP billet steel flywheel (must be purchased, balanced with rotating assy)
-Spec Stage 3 Ceramic clutch
-Joe overton ground cam 242/250 @50 .558/.558
-Rollmaster billet timing set
-Comp R lifters
-trick flow 7.150" pushrods .080 wall
-Comp Promagnum rockers
-Comp 977 springs
-comp spring hardware 4771/611/740
-Ferrea 2.0"/1.56" 6000 series stainless valves
-Lloyd Elliot ported LT1 castings (flow sheet upon request)
-Lloyd Elliot ported LT1 intake (provision for 58mm)
-Accell 30# injectors
-CSI electric H2O pump
-Rebuilt Vented '96 Opti (if you have a newer opti I wont install the WP so you can install your own)
Also for sale
BMR kmember $325
C5 brake conversion w/wilwood pads $600
I have pictures of everything on my page, but no HTML for it, so ask me and ill link you directly to the picture of what you want
Last edited by jonaddis84; Apr 3, 2005 at 10:29 AM.
Registered User
Joined: Feb 2003
Posts: 1,661
From: Frisco TEXAS
Re: Interest in complete Forged 381?
Thread Starter
Registered User
Joined: Oct 2002
Posts: 1,639
From: Toledo, OH
Re: Interest in complete Forged 381?
Dreamer PM sent.
Texas, Kmember isnt out of the car yet, Im doing a head/cam install on a buddys car and pulling the motor, so I want to bolt it in there and make sure its still straight after the rollover, so Ill get with you later this week. Its red.
Chad...stock ported TB
Shurt...Injectors will only be forsale if I part out, if that happens $150
Texas, Kmember isnt out of the car yet, Im doing a head/cam install on a buddys car and pulling the motor, so I want to bolt it in there and make sure its still straight after the rollover, so Ill get with you later this week. Its red.
Chad...stock ported TB
Shurt...Injectors will only be forsale if I part out, if that happens $150
Thread Starter
Registered User
Joined: Oct 2002
Posts: 1,639
From: Toledo, OH
Re: Interest in complete Forged 381?
Ryan ported it. Looks pretty damn sweet. Probably not quite enough for a 383, but I had planned on replacing it soon enough. Seemed to work fine while it was on there though 
http://www.geocities.com/jonaddis842003/TBfront.jpg
http://www.geocities.com/jonaddis842003/TBtop.jpg
I actually have a better ported TB case, with no blades or anything in it if you want it.
http://www.geocities.com/jonaddis842003/TBfront.jpg
http://www.geocities.com/jonaddis842003/TBtop.jpg
I actually have a better ported TB case, with no blades or anything in it if you want it.