Well, I need the money so I need to sell my baby before I even get to hear her run . I never even had a chance to run this professionally built 355. It is balanced and blueprinted and it comes with the build sheets. Here are the specs:

1993 350 2-bolt main block with only 18k original miles on it, bored .030 over.
Forged ZZ4 Crank – Brand New!
Compression 9.25:1 – Great for a street engine for gas mileage at over 425hp! Or do what I was going to do and throw a stock procharger on there and make over 600hp on the street.
TRW Forged Pistons L2256F30 – Brand New!
Speed Pro Plasma Moly Rings – Cut to fit Rings. This goes along with the blueprinting
LT4 Hot cam – Brand new!
Forged 5.7 “Pink rods” Not the powdered metal kind, these are the old school kind used by lingenfelter. These are balanced and polished! No expense was spared!
Bearings – All Clevitte 77’s.
Complete Lingenfelter Super Ram, this is not your run of the mill Accell set, this is straight from lingenfelter, with the billet 58mm throttle body and all. I have both a superram base and an extrude honed Stock TPI base. This base wuill outflow the super ram base and the entire setup is all ghasket matched to each other.
Walbro High volume fuel pump 255lph – Brand New
Hooker 2055’s – Brand new, No Y pipe
Maf Wiring Harness
2 Mafs
24lb injectors (LT1)
AFPR
Fuel Rails
Heads – Here’s the really good part. AFR 195’s, professionally built! These heads had very little mileage on them, but I still had them cleaned, a serdi valve job performed, and had them blueprinted. They have manley valves and new valve seals, and springs that easily handle the LT4 hot cam, however I do not currently have the exact specs on them. These heads look BRAND NEW and make a LOT of power. Here’s the specs on them at 28”:

Intake
.050 36.5
.200 – 143.5
.300 – 196.4
.400 – 240.0
.500 – 261.9
.550 – 268.1
.600 – 271.2

Exhaust
.50 – 26.1
.200 - 109.1
.300 – 149.2
.400 - 178.5
.500 - 194.5
.550 - 199.8
.600 - 205.1

As you can see these heads flow some major air!

Basically the bottom end is a forged power pack of a ZZ4 that has blueprinted and balanced (something you don’t get with a ZZ4! The block has also been painted red. Easy to repaint, but I think it looks awesome with the chrome look of the AFR heads. This is a pretty complete engine. Plug your water pump on and your oil pan and your good to go! I have spent well over $8k on this engine, and hate to see it go, but I need the cash. I am asking $5,000 for the entire thing. I will split shipping with you on the engine. It needs to go to a good home. Email me with any questions you may have.

James
Robbins1129@aol.com

Open to trades + cash
Need a complete dash from a 98 Camaro, including wiring.
Possibly a rear end
Leather interior... I am open

 

TTT

I am somewhat open on the price, and may even part out if the price is right. I have the buildsheets

 

still have any of this?

 

The hooker 2055's are sold, the LT1 injectors are sold, but everything else is ready to go. I also have a brand new set of SLP 30001 Headers, still in the package from SLP.

 

i'm particularly looking for a super ram....

 

Hi, I do have the super ram. It comes with the 58mm TB, New super ram base, runners, Flat top Plenum, Fuel Rail and AFPR, as well as brand new gaskets from Summit, as well as new bolts, I believe they are stainless, but need to check. Shoot me an email with an offer and I can send you a few pics.

James

 

what are you looking to get for the heads? and are those flow numbers unported? ( out of the box)

 

TriPinTAz,

Shoot me an email. I just had a Serdi Valve job done to them and they are ready to go. Only about 5000 total miles on the heads since new. Upgraded hardware on them, etc... I would like to get $1200 shipped.

 

i've tried to send you emails with no replies back from you. if you want to sell the superram plenum, runners, fuelrails email me at oddiez@hotmail.com