Harwood lt1 hood, BMR subframes, Spohn T/A, and Eibachs, 9" moser
Thread Starter
Registered User
Joined: Jul 2001
Posts: 338
From: Mentor, Ohio, USA
Harwood lt1 hood, BMR subframes, Spohn T/A, and Eibachs, 9" moser
I have a Harwood hood off my 96 Z. It is in good condition but the top needs repainted, it is black and has flat black covering scoop due to a cat got on there and scratched the paint, so I lightly sanded it and painted it. It has a small chip in the pass. side corner, a easy easy fix, I had it on for 2 yrs and no one noticed. I would like $375.00 plus shipping or you can pick it up. It will be shipped in a box that is correct size with corner protection and foam on sides. An automatic $15.00 insurance fee will be added because I don't want any problems. New the hoods go anywhere from $465.00 to $550.00 plus shipping.
SOLD!!!!!
Pics here http://www.cardomain.com/ride/362741/5
Next: I bought a pair of BMR Subframes off ebay 2 1/2 yrs. ago and I could never find someone to weld them on, there are no good welders in my area.
The subrames are boxed, they were off a 97 firebird that was hit in the front.
When I got them, they were red but the powdercoat was chipping off so I coated them with rustoleum black. I paid $125 for them and I will take a loss
to get them out of my garage. $95.00 plus shipping. I had to buy slp bolt-ons
which I don't like, someday i will find someone to weld them on.
SOLD!!!
Pics here: http://www.cardomain.com/ride/362741/8
Third: I have a spohn torque arm with crossbrace, drive shaft loop, and angle finder. I bought it because I thought I was going to go extreme and build a drag car but I have a baby now and do not have the money to go all out. It has less the 1000 miles on it. It did make a huge difference in accleration, braking and handling. It is in perfect condition. It has poly front bushing and straight crossbrace which fit all stock stlye y pipe exhaust, kooks headers, and pacesetter long tubes with pacesetter y-pipe(this is what I run). I paid $435.00, I am asking $350.00 plus shipping.
SOLD!!!
Pics here http://www.cardomain.com/ride/362741/6
Next: I have a set of front Eibach Sportlines for LT1.
I bought them before I got the 9 inch rear so i could get a raked look with pro-kit rears. now I don't need them. $60 shipped
Sale Pending, moose is second in line
Pics here: http://www.cardomain.com/ride/362741/8 look at bottom of page
I also am looking to sell my rear end. It is a moser axle and housing kit with strange case with 3.89 us gears, tru-trac locker(quiet version), big pinion support, moser 1350 yoke, 31 spline, spohn lca's and sway bar brackets.
It has 2,156 miles on it. It was only draged on 2 passes. This was set up by John Petto. John has set up rear ends for summit racing and multiple racers at Norwalk Raceway. It is set up very quiet which is rare for 3.89's. It only has a small wine from 52 miles an hour to 63 miles an hour. You have to really pay attention to hear it. I added it all up and I have $2,522.54 in receipts in this rearend with labor from John. It has only ran Royal Purple in it.
I am asking $1900 Plus shipping for it. It can be sold with LT1 brake brackets on it but I will need yours so I can put my stock rear back in. If not, I will remove them. When it is shipped, the axle housing and axles will be sent in one box and center section sent in another to save on weight, it will be cheaper this way.
Email is: ecstazz28@sbcglobal.net
Thanks for looking
Steve
SOLD!!!!!
Pics here http://www.cardomain.com/ride/362741/5
Next: I bought a pair of BMR Subframes off ebay 2 1/2 yrs. ago and I could never find someone to weld them on, there are no good welders in my area.
The subrames are boxed, they were off a 97 firebird that was hit in the front.
When I got them, they were red but the powdercoat was chipping off so I coated them with rustoleum black. I paid $125 for them and I will take a loss
to get them out of my garage. $95.00 plus shipping. I had to buy slp bolt-ons
which I don't like, someday i will find someone to weld them on.
SOLD!!!
Pics here: http://www.cardomain.com/ride/362741/8
Third: I have a spohn torque arm with crossbrace, drive shaft loop, and angle finder. I bought it because I thought I was going to go extreme and build a drag car but I have a baby now and do not have the money to go all out. It has less the 1000 miles on it. It did make a huge difference in accleration, braking and handling. It is in perfect condition. It has poly front bushing and straight crossbrace which fit all stock stlye y pipe exhaust, kooks headers, and pacesetter long tubes with pacesetter y-pipe(this is what I run). I paid $435.00, I am asking $350.00 plus shipping.
SOLD!!!
Pics here http://www.cardomain.com/ride/362741/6
Next: I have a set of front Eibach Sportlines for LT1.
I bought them before I got the 9 inch rear so i could get a raked look with pro-kit rears. now I don't need them. $60 shipped
Sale Pending, moose is second in line
Pics here: http://www.cardomain.com/ride/362741/8 look at bottom of page
I also am looking to sell my rear end. It is a moser axle and housing kit with strange case with 3.89 us gears, tru-trac locker(quiet version), big pinion support, moser 1350 yoke, 31 spline, spohn lca's and sway bar brackets.
It has 2,156 miles on it. It was only draged on 2 passes. This was set up by John Petto. John has set up rear ends for summit racing and multiple racers at Norwalk Raceway. It is set up very quiet which is rare for 3.89's. It only has a small wine from 52 miles an hour to 63 miles an hour. You have to really pay attention to hear it. I added it all up and I have $2,522.54 in receipts in this rearend with labor from John. It has only ran Royal Purple in it.
I am asking $1900 Plus shipping for it. It can be sold with LT1 brake brackets on it but I will need yours so I can put my stock rear back in. If not, I will remove them. When it is shipped, the axle housing and axles will be sent in one box and center section sent in another to save on weight, it will be cheaper this way.
Email is: ecstazz28@sbcglobal.net
Thanks for looking
Steve
Last edited by INSANEZ; Jan 6, 2007 at 06:40 AM. Reason: forgot email and add status' of sales
Thread Starter
Registered User
Joined: Jul 2001
Posts: 338
From: Mentor, Ohio, USA
I know it is not the same but I will try to give to a visual. The gaps are
about a 4.5 out if 5 compared to stock. They were even on both sides. It did not hit or bind on aything. Headlight area matched up perfect on both sides. The flat black look on scoop needs to go, must paint it. the chip is from when I took it off any set it on the corners, dumb move on my part.
Again, I hope that helps.
Steve
about a 4.5 out if 5 compared to stock. They were even on both sides. It did not hit or bind on aything. Headlight area matched up perfect on both sides. The flat black look on scoop needs to go, must paint it. the chip is from when I took it off any set it on the corners, dumb move on my part.
Again, I hope that helps.
Steve
Thread Starter
Registered User
Joined: Jul 2001
Posts: 338
From: Mentor, Ohio, USA
On the rear end, moser did not put on the abs rings. so you would get a abs light. Other than that no lights. My abs still works in the front, you can get the abs rings from moser from what i was told.
Sorry, no trades, I need the money, got a kid on the way.
thanks
Steve
Sorry, no trades, I need the money, got a kid on the way.
thanks
Steve
