FS: Fully ported race lt1 heads, springs, and 1.6 rockers COMPLETE
04-12-2004, 10:17 PM
#1
Registered User
Thread Starter
Join Date: Feb 2001
Location: Cincinnati, Ohio
Posts: 3,068
FS: Fully ported race lt1 heads, springs, and 1.6 rockers COMPLETE
Fully ported lt1 heads by Dave Smith (LT1Dave)
Manley 202/156 Backcut and 3 angle valve job by BES (tony bischoff's place, best money can buy)
Complete with k-motion k-800 springs, retainers, locks, etc. All set up already.
Comes with 1.6 lt4 roller rockers
The car went 12.0s with 383 motor and a hydro roller cam similiar to 847. Heres the kicker. Tranny wasnt working due to improperly installed manual valve body kit. Car launched in 1st and went straight into 3rd gear and still ran those times.
These heads were not flowed, but other stuff comming out of LT1 daves shop is in the high 270/low 280 CFM range at .600 with good midlift as flowed on BES flow bench. THESE HEADS WILL (and did) MAKE AWESOME POWER. Put these in the AI range of heads from results i have seen. Riding in this car made mine feel SLOW.
Heads have 1,200 miles on them. Selling for a buddy who is going with a dart block so he no longer has use for them.
1600 OBO
Manley 202/156 Backcut and 3 angle valve job by BES (tony bischoff's place, best money can buy)
Complete with k-motion k-800 springs, retainers, locks, etc. All set up already.
Comes with 1.6 lt4 roller rockers
The car went 12.0s with 383 motor and a hydro roller cam similiar to 847. Heres the kicker. Tranny wasnt working due to improperly installed manual valve body kit. Car launched in 1st and went straight into 3rd gear and still ran those times.
These heads were not flowed, but other stuff comming out of LT1 daves shop is in the high 270/low 280 CFM range at .600 with good midlift as flowed on BES flow bench. THESE HEADS WILL (and did) MAKE AWESOME POWER. Put these in the AI range of heads from results i have seen. Riding in this car made mine feel SLOW.
Heads have 1,200 miles on them. Selling for a buddy who is going with a dart block so he no longer has use for them.
1600 OBO
Last edited by atljar; 04-12-2004 at 10:46 PM.
04-13-2004, 07:23 AM
#4
Registered User
Thread Starter
Join Date: Feb 2001
Location: Cincinnati, Ohio
Posts: 3,068
No pictures, sorry.
I'll shoot the two of you a shipping quote this afternoon once I am home from work.
Willing to negotiate on all of it, also willing to break apart the 1.6 rockers, but not the valvetrain and valves.
I'll shoot the two of you a shipping quote this afternoon once I am home from work.
Willing to negotiate on all of it, also willing to break apart the 1.6 rockers, but not the valvetrain and valves.
04-15-2004, 01:09 AM
#7
Registered User
Join Date: Dec 2002
Location: Decatur, Al
Posts: 31
Those the hotcam kit roller rockers? Can you sell the springs, locks and retainers too? How much for all or just the roller rockers shipped to 35603?
Last edited by redlt1camaro2k2; 04-15-2004 at 01:53 AM.
04-15-2004, 06:56 AM
#11
Registered User
Join Date: Nov 2001
Location: north carolina
Posts: 408
would you trade a brand new NX system with genx comes with 15lb for the heads. Everthing still in wrapping
prince.l@charter.net
p/n 20118-10 100-250hp
prince.l@charter.net
p/n 20118-10 100-250hp
