**PLEASE NOTE: All parts have only been ASSEMBLED, none of the parts listed below have ever been "fired" before. Just ASSEMBLED.**

Turbo/Blower Rotating Assembly
-TRW turbo/blower pistons list for $320 a set Link to description
-CAT H-beam rods list for $377 Link to description
-Federal Mogul Coated main and rod bearings list for $50 a set Link to description
-Speed Pro Plasma Moly rings list for $100 link to description
-Chevy Forged Z28 crank (for a 2 piece block)

All of the above is balanced and ready to go, to duplicate would cost you roughly $1200 with a value of $150 for the crank and $100 of balancing.

I want LOWERED TO $500. I will separate if needed but would rather sell as a rotating assembly for someone so you can just throw it in and be done. Also the crank has been cut, i believe the mains are .010 and the rod journals are .020. Again, above has only been assembled not run.

ARP Accessories
-Main studs for use with a windage tray and 4 bolt main list for $73 link to description
Sell for $25

Tires

-Mickey Thompson ET Fronts 27.5 x 4.5. Still a lot of tread left, they list for $134 EACH for a total of $260. Sell for LOWERED TO $100

Wheels
Here is a link to the bogarts for sale

-- Bogart Fly Stars. These are the cheaper line of wheels, here is a link:
http://www.bogartracingwheels.com/wheels/flystar.jpg
Rears are 15x10 with 6.5" of backspacing and the fronts are 15x3.5 with i think 2 3/4" of backspacing. They come with centercaps and M12 lugnuts for the fronts and 1/2 lugs for the rears.

Rears retail for $299 a piece
Fronts retail for $189 a piece

I'll take $LOWERED TO $400 for all 4 rims (You get the centercaps and lug nuts for free; they're worth $60)

Engine Accessories
-CAT SFI balancer, here is a link. They retail for $150, sell for $75
-Aluminum timing chain cover, here is a link to picture. Cost me $20, sell for $10 Comes with all the needed allen bolts


[
-Miller Engineering Mid-Lift roller rockers. These are truly a thing of beauty. Jim Miller invented and PATENTED the idea of mid-lift geometry in roller rockers 20 years ago and now even Comp Cams is using his ideas to for their own mid-lift rockers (see Comp Cams new shaft system). The patent expired so others are using the technology. These are simply the best you can buy in my opinion and these are brand new, they were just installed. Here is a link to pictures. Despite their big look they still fit under short valve covers. These sell for $288 new PLUS YOU GET THE FREE GEOMETRY TOOL TO SETUP YOUR VALVES FOR FREE ($130 VALUE!). That's $420 worth of stuff for LOWERED TO $150.

Turbos

60-1 turbo, brand new compressor wheel and brand new turbine wheel. This turbo is a rebuild in excellent new condition with no run time on it. This is a big housing 60-1 except it has the small inlet and outlet. What this means is that if you want to install the large housing cover (4" inlet, 2.5" outlet) you can, it will bolt right on. Right now the current cover has a 3" inlet and a 2" outlet.

60mm compressor wheel
P-trim turbine wheel
69a/r (on-center housings)

LOWERED TO $450 shipped


Transmission and Accessories

-Th400 transmission in good working order....i believe there is a shift kit in it but i am not 100% sure. $250
-Midwest torque converter, this is there 1000ftlb guarranteed converter. Built for a boost motor and about a 3500 stall behind a 355. Cost is $570, i'll sell for $375
-CAT SFI flexplate, 168 tooth, $15

Rearend

Dana 44 for thirdgen, brand new hardened Moser axles to be legal for 10.99 and faster. 3.54 gear with perfect wear and almost no miles. Aluminum calipers with brand new brake pads. Pour in oil and its ready to go.

$1000 and your rearend Must be for a thirdgen and have same style brakes.




---------------
That's all for now, i will be adding other stuff later. Anyone who is interested in anything for the prices above or other offers please feel free to email me @ koby12@ureach.com or call my Cell Phone @ 773-617-1765

Jimmy

 

Can you email or PM some info on the Roller rockers...looking for some and havent really heard of this mid-lift thing before.

LMK
Joe

 

TTT

 

TTT make some offers

 

TTT, some stuff sold

A 60-1 turbo was added

 

how bout $35 shipped over to detroit for the arp stud kit? I'll have to check that I can use that on my 4 bolt LT1 eng. first though. if not I can use it on my Iroc eng. since its also a 4 bolt. email me so I can get back to you.
chris

 

how much of an improvement would these heads be over my stock lt1 heads. may be interested. thanks.


-Daniel

 

how much HP is that turbo capable of?? also what is the manufacturer?

 

These are Brodix Track 1 heads for a small block chevy, they will not work on an LT1 unless you convert them to reverse cooling

The turbo is capable of a solid 550hp but many have pushed it to 600hp but that is with an highly optimized combination but 500-550 should be expected.

It is a garrett turbo

 

you never emailed about the stud kit. email me please.
chris

 

Interested in the balancer... 110.00 shipped

email me at snug12@aol.com

 

Sorry, the studs aren't available anymore. I can't find my original main bolts so i need to keep the studs in there.

 

Email sent on the balancer.......

Everything else is still for sale and i need to get rid of it ALL.

Make offers

 

TTT.....any reasonable offer will not be refused

 

TTT.....everything must go