97Z RIP /Parting out
Thread Starter
Registered User
Joined: May 2004
Posts: 85
From: Westchester, NY
97Z RIP /Parting out
Well of course AFTER I get my car together is when someone decides to run a red light and smash it, so I have to part it out:
97 Z28 6M, silver w/graphite leather, 58K miles, hit in the front.
FRESH LT1 ONLY 4K miles: [B]STILL AVAIL, Make an offer.[B]
**Motor Professionally built and Blueprinted by Automotive Precision Machine in Highland, NY with specs available on request.
**All new internals (except crank and rods, which were cleaned and polished) including Mahle (KB Hyperutentic) std bore pistons (block did not need Boring), and timing chain.
**GM LT4 hot-cam kit with Comp Cams roller rockers, new pushrods.
**Stock heads redone with a 3-angle valve job and shaved .012".
**New Opti, Plugs, Wires and MSD coil.
**PCM with MadZ28 tune and complete wiring harness.
Reciepts totalling $3740...REDUCED!!! $2500-MUST SELL!!!
STILL AVAIL, MAKE AN OFFER!!!
STILL AVAIL, Make an offer.Used Adjustable Fuel Pressure Regulator: Aeromotive AEI13107 in Summitt for $155. Paid $110 used and never installed.......REDUCED!! $75-OBO.
SOLD!!!BBK chrome shorty headers also w/ 4K miles and 2 new 2 1/2" cartek cats.
SOLD!!! Brand new (literally was on the car only 10 days) Magnaflow stainless steel cat-back.
SOLD!!! Entire car less Engine and Tranny: Interior in great condition, good 3.42 traction control rear, good pass door and hatch, good T-Tops, factory rims with good Kuhmo rubber.
The motor is in lower Westchester, NY zip 10538....E-mail and/or PM me with offers.
Rick
97 Z28 6M, silver w/graphite leather, 58K miles, hit in the front.
FRESH LT1 ONLY 4K miles: [B]STILL AVAIL, Make an offer.[B]
**Motor Professionally built and Blueprinted by Automotive Precision Machine in Highland, NY with specs available on request.
**All new internals (except crank and rods, which were cleaned and polished) including Mahle (KB Hyperutentic) std bore pistons (block did not need Boring), and timing chain.
**GM LT4 hot-cam kit with Comp Cams roller rockers, new pushrods.
**Stock heads redone with a 3-angle valve job and shaved .012".
**New Opti, Plugs, Wires and MSD coil.
**PCM with MadZ28 tune and complete wiring harness.
Reciepts totalling $3740...REDUCED!!! $2500-MUST SELL!!!
STILL AVAIL, MAKE AN OFFER!!!
STILL AVAIL, Make an offer.Used Adjustable Fuel Pressure Regulator: Aeromotive AEI13107 in Summitt for $155. Paid $110 used and never installed.......REDUCED!! $75-OBO.
SOLD!!!BBK chrome shorty headers also w/ 4K miles and 2 new 2 1/2" cartek cats.
SOLD!!! Brand new (literally was on the car only 10 days) Magnaflow stainless steel cat-back.
SOLD!!! Entire car less Engine and Tranny: Interior in great condition, good 3.42 traction control rear, good pass door and hatch, good T-Tops, factory rims with good Kuhmo rubber.
The motor is in lower Westchester, NY zip 10538....E-mail and/or PM me with offers.
Rick
Last edited by StumpDeisel; Jan 7, 2005 at 03:44 PM.
Thread Starter
Registered User
Joined: May 2004
Posts: 85
From: Westchester, NY
Re: 97Z RIP /Parting out
Originally Posted by blackbirdta
i thought i read 7500 for the car less engine/tranny 
you can definately make more than 750 off all that...
you can definately make more than 750 off all that...
I'm sure I could, but the car is on my mechanic's lift w/ no front end on it, and I don't have the luxury of waiting to part it all out, hence the $750 to get it out of his shop asap. If you can flat-bed it out feel free to take what you need and recoup your costs by parting out the rest.
Registered User
Joined: Oct 2003
Posts: 2,140
From: DOVER DE
Re: 97Z RIP /Parting out
Please send pics of interior dash and seats. Is the front bumper intact? Will the car roll to be moved on a tow dolly? Whats your zip?
Thanx
REANDCHERYL@MSN.COM
Thanx
REANDCHERYL@MSN.COM
Thread Starter
Registered User
Joined: May 2004
Posts: 85
From: Westchester, NY
Re: 97Z RIP /Parting out
Originally Posted by RE AND CHERYL
Please send pics of interior dash and seats. Is the front bumper intact? Will the car roll to be moved on a tow dolly? Whats your zip?
Thanx
REANDCHERYL@MSN.COM
Thanx
REANDCHERYL@MSN.COM
Zip 10538, pics otw.
Thread Starter
Registered User
Joined: May 2004
Posts: 85
From: Westchester, NY
Re: 97Z RIP /Parting out
Originally Posted by gtkilr95
how much for headers and exhaust what about the pcm
The cat-back is brand new, Stainless magnaflow, 2 stainless catco cats from summit, asking $300
The headers are BBK chrome shorties, asking $150.
The y-pipe is damaged on the driver's end, and would include it w/ the exhaust.
The PCM is a standard Hotcam tune from MADZ28, and plan to sell that with the motor...
Registered User
Joined: Oct 2002
Posts: 3,958
From: Middeltown NY
Thread Starter
Registered User
Joined: May 2004
Posts: 85
From: Westchester, NY
Re: 97Z RIP /Parting out
Originally Posted by 1984camaroz28
IM me or e-mail me some pic to onefastz28@optonline.net
PM sent