94 camaro car or parts
Thread Starter
Registered User
Joined: Dec 2003
Posts: 117
94 camaro car or parts
*New Revised*
I have a 94 Camaro that I have been working on for 3 years. I have over $60,000 into it. I dropped it off at Firestone for an alignment and they smacked the oil pan against the hoist and then fried the motor. I dont have anymore money to put into it so it's up for sale. I want to sell it whole if I can but, if I get enough offers on the parts, I will part it. I would like $18,000 for it all as is. If interested in a part make an offer, you guys know what thry retail for. The motor is torn out right now. The only thing that it needs to be whole again is a new crank and oil pump, to hone the bores, and maybe new rods and pistons, but that is debatable. You could get a $60,000 car for very cheap. The nitrous kit was never used execpt on the dyno. No stress to all the parts, I never got to pull the trigger. Everything it has is below.
Link to pictures of the car http://pg.photos.yahoo.com/ph/swasenko/album?.dir=/c688
ARP Headbolts, Felpro gaskets, LT-1 block bored .030 over- $250
Stock rims w/ Bridgestone RE730's Z speed
ZO6 high polished rims with BF Goodrich Comp TA Drag radials, never driven on$2000
AFR 195cc, 76cc com., Stage III competition heads- $2000
Cam motion cam(Can find extact specs yet, will get em)
LT4 Ported intake- $175
LT4 rockers- $150
Lunati Timing chain- $50
Moroso high polished valve covers- $100
March underdrive pulleys- $75
MSD Coil- $20
MSD 8mm wires- $75
MSD 6-btm ignition- $350
Ramchargers high flow water pump- $75
Adjutable fuel pressuer regulator- $100
Nitrous works wet kit- $400
MSD boost retard controller- $125
42# injectors- $300
Moroso 7 quart oil pan- $150
Optima red top deep cycle battery
BBK 58mm throtle body- $225
Ported MAF- $125
K&N Cold air intake- $125
New flywheel, Turbo 400 trans, Custom built 2800 stall convertor- $2200
Eagle 383 stroker kit
Everything below is all together as a rolling chasis:
Brand new PCM
Brand new TPS sensor
I have 7 quarts of Royal Purple oil and 2 new filters
Custom fit car cover
Limo black rear window
Hypertech programmer
3in aluminum drive shaft
Drive shaft safety loop
Moser 12 bolt, 33 spline axles, 3.73 gear ratio
AGI solid sway bar
Custom machined adjutstable aluminum lower control arms
BMR adjustable panhard bar
BMR Sub-frame connectors
BMR shock tower brace
Koni adjustable 8 stage rear shocks
Wolfe 6 pt. roll cage with swing out door bars, both sides
Head and tail light covers
Harwood ram air cowl induction hood
Alpine 9200 headunit
Boston Acoustics Rally series 6.5 components and 1in tweeters
Kenwood 6.5in with center mounted swivel tweets
JL Audio 10 W3 sub w/ Q-logic encolsure that fits in body panel
Rockford Fostgate 200.4 amp
Kicker 300.2 amp
Eibach lowering springs
3 in dual flowmaster exhaust
Dual radiator fans
dual A-pillar pod
Boost guage
Auto meter fuel pressure guage
Drilled and slotted rotors
Plus many other extras I probably forgot Whole chasis with all listed- $10,000
Everything on this car is top notch. I did it all right. Please email or call me(preferred) with any questions at 313-980-1428.
Steve
I have a 94 Camaro that I have been working on for 3 years. I have over $60,000 into it. I dropped it off at Firestone for an alignment and they smacked the oil pan against the hoist and then fried the motor. I dont have anymore money to put into it so it's up for sale. I want to sell it whole if I can but, if I get enough offers on the parts, I will part it. I would like $18,000 for it all as is. If interested in a part make an offer, you guys know what thry retail for. The motor is torn out right now. The only thing that it needs to be whole again is a new crank and oil pump, to hone the bores, and maybe new rods and pistons, but that is debatable. You could get a $60,000 car for very cheap. The nitrous kit was never used execpt on the dyno. No stress to all the parts, I never got to pull the trigger. Everything it has is below.
Link to pictures of the car http://pg.photos.yahoo.com/ph/swasenko/album?.dir=/c688
ARP Headbolts, Felpro gaskets, LT-1 block bored .030 over- $250
Stock rims w/ Bridgestone RE730's Z speed
ZO6 high polished rims with BF Goodrich Comp TA Drag radials, never driven on$2000
AFR 195cc, 76cc com., Stage III competition heads- $2000
Cam motion cam(Can find extact specs yet, will get em)
LT4 Ported intake- $175
LT4 rockers- $150
Lunati Timing chain- $50
Moroso high polished valve covers- $100
March underdrive pulleys- $75
MSD Coil- $20
MSD 8mm wires- $75
MSD 6-btm ignition- $350
Ramchargers high flow water pump- $75
Adjutable fuel pressuer regulator- $100
Nitrous works wet kit- $400
MSD boost retard controller- $125
42# injectors- $300
Moroso 7 quart oil pan- $150
Optima red top deep cycle battery
BBK 58mm throtle body- $225
Ported MAF- $125
K&N Cold air intake- $125
New flywheel, Turbo 400 trans, Custom built 2800 stall convertor- $2200
Eagle 383 stroker kit
Everything below is all together as a rolling chasis:
Brand new PCM
Brand new TPS sensor
I have 7 quarts of Royal Purple oil and 2 new filters
Custom fit car cover
Limo black rear window
Hypertech programmer
3in aluminum drive shaft
Drive shaft safety loop
Moser 12 bolt, 33 spline axles, 3.73 gear ratio
AGI solid sway bar
Custom machined adjutstable aluminum lower control arms
BMR adjustable panhard bar
BMR Sub-frame connectors
BMR shock tower brace
Koni adjustable 8 stage rear shocks
Wolfe 6 pt. roll cage with swing out door bars, both sides
Head and tail light covers
Harwood ram air cowl induction hood
Alpine 9200 headunit
Boston Acoustics Rally series 6.5 components and 1in tweeters
Kenwood 6.5in with center mounted swivel tweets
JL Audio 10 W3 sub w/ Q-logic encolsure that fits in body panel
Rockford Fostgate 200.4 amp
Kicker 300.2 amp
Eibach lowering springs
3 in dual flowmaster exhaust
Dual radiator fans
dual A-pillar pod
Boost guage
Auto meter fuel pressure guage
Drilled and slotted rotors
Plus many other extras I probably forgot Whole chasis with all listed- $10,000
Everything on this car is top notch. I did it all right. Please email or call me(preferred) with any questions at 313-980-1428.
Steve
Last edited by swasenko; Jul 30, 2005 at 08:44 PM.
Thread Starter
Registered User
Joined: Dec 2003
Posts: 117
Re: 94 camaro car or parts
I'm in Canton, MI. Only about 45 min from Goodrich. I would like $1500 for the rims and tires. I spent over $3000 on them. They are 17x8.5 in front and 18x10 in rear. The rears have a 295 width on them.
Registered User
Joined: Jan 2005
Posts: 192
Re: 94 camaro car or parts
pics of the alpine headunit to gjonas24@gmail.com and how much would you want for it?
Registered User
Joined: Aug 2001
Posts: 452
From: CT
Re: 94 camaro car or parts
will you sell the bracket that holds the alternator and power steering pump to the motor? PM me or email me sentenced1304@yahoo.com soon if you can, thanks!
Registered User
Joined: Aug 2000
Posts: 691
From: Dearborn,MI. U.S.A.
Re: 94 camaro car or parts
I will take the coil and what condition is the optima in? also what are you asking for it? t120r@msn.com Steven
Banned
Joined: Jan 2002
Posts: 1,935
From: Mobile, Ala..USA
Re: 94 camaro car or parts
How much for
Please price individually
Harwood hood
Wolf roll cage
Drilled and slotted rotors all 4
Thanks
David
Speedadikk@comcast.net
Please price individually
Harwood hood
Wolf roll cage
Drilled and slotted rotors all 4
Thanks
David
Speedadikk@comcast.net
Registered User
Joined: Jul 2005
Posts: 1,783
Re: 94 camaro car or parts
How much would you like for the MAF and the Alluminum intake elbow you have? pics to scwizzo@yahoo.com please.