Alright well I first want to say that the only reason I'm selling this stuff is because I need the money. Otherwise, there's no way I would let this stuff go. First on the list is a complete 350. I can't tell you too much about the motor because it came in a 1969 camaro that I bought pretty cheap (which I'm selling for $4,000 no motor or transmission). Aparently the guy was going to run nitrous on it but decided to use a big block instead and never got around to it. So I bought it off him to finish what he started but like I said, money ran tight. I do know that it does have a Holley carb., Edelbrock intake manifold, scorpion 1.6 rollar rockers, Hooker Long Tube Headers, etc. This motor was built to throw you in your seat (I know from experience before I pulled it out)
. I'm selling it for $3,000 (was told it ONLY has about 5,000 miles on it) which also includes a TH350 tranny with a shift kit and a slap shifter (pretty sure that's what it is cause it's a 3 speed auto).The 454 is not built. The block is a Gen VI block (96+) that has been bored 30 over makin' it a 460 and has NEVER been used. The 454 Block I'm selling for $1,000. I also have a set of Speed Pro Pistons for the 454, an ESP (Eagle Specialty Products) Forged 4340 Crankshaft, Crane Cams Powermax hydraulic Rollar Special (check part # 168741 for specs or just email me), and the connecting rods are ESP H-Beam connecting rods. If you have any questions and or want to see pictures if you're interested you can e-mail me at Camaro468ci@netscape.net

 

you guys know that this is a deal to make anyone that wants a classic muscle car fixer upper or to do an engine swap go

 

send me some pictures of the camaro. Also what state are you located in?

send pictures to jy211@hotmail.com

 

I forgot to mention that the car does come with the set of 15" Weld Prostar Rims and Mickey Thompson ET street tires, all of which have "barely" been driven on. Sadly I can't remember width of the rims. It did come with a set of rims from a 1970 or 1971 camaro (I believe) with bald tires which I will also throw in with the car, the driveshaft which I believe is alluminum considering I can pick it up with a few fingers.

 

How much for 69 Camaro? The Gen VI block comes w/all parts listed for 454 for 1000.00? Do you have any pics of car? Is it a Z28 or other?

 

the camaro is going for $4,000, it used to be a 6 cylinder but the guy threw a 350 and I believe a 12-bolt rear end in it. The 454 block has been bored 30 over and is going for $1,000 by itself, the other parts are separate and yes i have pics. Just send me an e-mail and I will send them to you.

 

great deals

 

here are some of the pics that I have of the car, engine, and parts ... http://pg.photos.yahoo.com/ph/annv30.../ph//my_photos

 

fixed link

 

I want to come look at the camaro, just trying to make time....are you firm on the $4000 for the car? Or is there room to work?

 

yeah, what he said

 

I live in Oldsmar FL (which is in between Clearwater and Tampa), the price on the car is a firm $4,000 because I do have nice size credit card debts that REALLY need to be fixed if anyone is still interested in the car, send me an e-mail or a pm and I'll reply to you with my cell number and driving directions if needed.

 

kinda interested in the Camaro,how are the floor pans in it? is it a 12 bolt?

 

I "believe" the floor pans have been changed already because they don't have any major rust damage anywhere and yes it is a 12 bolt rear. I am going to try and take some pictures of the trunk and the floor pans tomorrow and post them up.

 

just uploaded some new pics of the car ... new pics of the car