1991 Z28 in Mi for sale
12-02-2006, 12:04 PM
#1
Registered User
Thread Starter
Join Date: Mar 2006
Location: Grand Rapids, Mi
Posts: 40
1991 Z28 in Mi for sale
Car is a 1991 Z28. T-Top car. originally was 305/700r4. The odo reads 200k miles but it was repainted recently. Also the motor has about 10k. Body has small dents here and there and previous owner painted over some stripes on drivers side door, but not very noticeable from 10 feet. rear bumper support rusted out so will need replaced. Previous owner installed 6 point cage. Has grey interior, carpet has stains in the fronts but overall interior is very very clean.
Floorboards had rust on them but i stripped them with a wire wheel and then POR 15'd back to the rear end.
-installed new 255lph fuel pump about 1000 miles ago
-installed new front to rear brake line after original broke.
-new posi/3.73 10 bolt installed. Has PBR disc brakes and axle tubes welded.
-original Z28 wheels stripped and polished.
-has custom y pipe and single 3 inch exhaust, no cats, hooker aerochamber single 3 inch inlet/outlet muffler.
If i sell the parts separate these would be my prices.
T-56 Tranny with pedals, centerforce 2 piece RMS 153 tooth flywheel, clutch, hydraulics. unknown mileage $1500 pickup only
400 bare block all machined and ready to be assembled. Bored .030 over, honed, magged, decked etc. 817 casting 2 bolt mains $650 pickup only
DART Iron Eagle Platinum Series heads. 200cc runners, 64 cc chambers springs good to .600 lift. $730 shipped
Edelbrock Victor Jr heads. 215cc runner 64cc chamber. Also custom CNC port work done. Also comes with brand new titanium valves and springs good to .630 $1000 + shipping
Holley Stealth Ram Injection setup. includes polished plenum, base, fuel rails, 24 lb injectors(cost $150), Kirban adjustable billet FPR(cost about $100), SS braided fuel lines, vacuum fittings, t stat housing, small cap distributor $700 for it all
BBK 52mm throttle body for 90-92 TPI $200
Hooker Super Comp 1 3/4" ceramic coated headers. Have some dents in them for starter and #7 plug but overall very good condition. $175 + shipping
Moroso high capacity oil pan for 82-92 f body with 2 piece RMS. painted VHT red $100+ shipping
Right now the car runs and drives fine, has a 357 with the dart heads, HSR on it but i think it will need new bearings cause the oil pressure gets to about 10 psi at idle when its warm. Has the 700r4 also installed right now but it is tired. Had a custom tune done by a thirdgen member when the motor went in but could use another tune up. I wouldnt be afraid to drive the car anywhere though. I was goind to do a 406/T56 swap this winter but am too busy with school and work and want to save up for a 5th gen.
Right now i would really like to sell everything as a package for someone to finish what i started. If theres enough interest in all other parts may sell it as a roller. total package with all parts listed i would start at $7500 obo
Im sure theres even more new stuff i cant think of right now.
E mail me at ZCap91@yahoo.com for pics
Floorboards had rust on them but i stripped them with a wire wheel and then POR 15'd back to the rear end.
-installed new 255lph fuel pump about 1000 miles ago
-installed new front to rear brake line after original broke.
-new posi/3.73 10 bolt installed. Has PBR disc brakes and axle tubes welded.
-original Z28 wheels stripped and polished.
-has custom y pipe and single 3 inch exhaust, no cats, hooker aerochamber single 3 inch inlet/outlet muffler.
If i sell the parts separate these would be my prices.
T-56 Tranny with pedals, centerforce 2 piece RMS 153 tooth flywheel, clutch, hydraulics. unknown mileage $1500 pickup only
400 bare block all machined and ready to be assembled. Bored .030 over, honed, magged, decked etc. 817 casting 2 bolt mains $650 pickup only
DART Iron Eagle Platinum Series heads. 200cc runners, 64 cc chambers springs good to .600 lift. $730 shipped
Edelbrock Victor Jr heads. 215cc runner 64cc chamber. Also custom CNC port work done. Also comes with brand new titanium valves and springs good to .630 $1000 + shipping
Holley Stealth Ram Injection setup. includes polished plenum, base, fuel rails, 24 lb injectors(cost $150), Kirban adjustable billet FPR(cost about $100), SS braided fuel lines, vacuum fittings, t stat housing, small cap distributor $700 for it all
BBK 52mm throttle body for 90-92 TPI $200
Hooker Super Comp 1 3/4" ceramic coated headers. Have some dents in them for starter and #7 plug but overall very good condition. $175 + shipping
Moroso high capacity oil pan for 82-92 f body with 2 piece RMS. painted VHT red $100+ shipping
Right now the car runs and drives fine, has a 357 with the dart heads, HSR on it but i think it will need new bearings cause the oil pressure gets to about 10 psi at idle when its warm. Has the 700r4 also installed right now but it is tired. Had a custom tune done by a thirdgen member when the motor went in but could use another tune up. I wouldnt be afraid to drive the car anywhere though. I was goind to do a 406/T56 swap this winter but am too busy with school and work and want to save up for a 5th gen.
Right now i would really like to sell everything as a package for someone to finish what i started. If theres enough interest in all other parts may sell it as a roller. total package with all parts listed i would start at $7500 obo
Im sure theres even more new stuff i cant think of right now.
E mail me at ZCap91@yahoo.com for pics
Thread
Thread Starter
Forum
Replies
Last Post
NewsBot
2010 - 2015 Camaro News, Sightings, Pictures, and Multimedia
0
12-03-2014 12:30 PM