Everyone in! 1/4 mile times and cheap parts
Re: Everyone in! 1/4 mile times and cheap parts
hey fellas i saw this and had to jump in:my old 91 z had stock bottom end,cc306,ported vette heads 2.00 1.56,mini ram 30lb inj.58 mm tb,2800 stall
needed more(3500) 3.73s,m&h racemasters ran 11.80-11.90,i had the typical mods like cai into the fender big k&n,pulleys,chip from perf.resources....all at sea level(HRP)...
needed more(3500) 3.73s,m&h racemasters ran 11.80-11.90,i had the typical mods like cai into the fender big k&n,pulleys,chip from perf.resources....all at sea level(HRP)...
Re: Everyone in! 1/4 mile times and cheap parts
[QUOTE=96m6lt1]hey fellas i saw this and had to jump in:my old 91 z had stock bottom end,cc306,ported vette heads 2.00 1.56,mini ram 30lb inj.58 mm tb,2800 stall
needed more(3500) 3.73s,m&h racemasters ran 11.80-11.90,i had the typical mods like cai into the fender big k&n,pulleys,chip from perf.resources....all at sea level(HRP)...(NOT EXACTLY CHEAP PARTS)however i did a 92z 5.7,5spd conv,slp runners,slp 495/510,pulleys,3.42s,tires,both cars ran hooker 1-5/8s 2.5" y-pipe to dual cats and 3"amer.thunder system,this one ran the fastest of 12.1 could not get an 11 to save my life
needed more(3500) 3.73s,m&h racemasters ran 11.80-11.90,i had the typical mods like cai into the fender big k&n,pulleys,chip from perf.resources....all at sea level(HRP)...(NOT EXACTLY CHEAP PARTS)however i did a 92z 5.7,5spd conv,slp runners,slp 495/510,pulleys,3.42s,tires,both cars ran hooker 1-5/8s 2.5" y-pipe to dual cats and 3"amer.thunder system,this one ran the fastest of 12.1 could not get an 11 to save my life
Re: Everyone in! 1/4 mile times and cheap parts
I went 15.1@91 with a pretty bad 60' (2.1x) with 5speed 305 TBI 3.42gears, no mods other than headers, catback and computer tuning.
I'm now running a single plane intake, with an UltraDyne cam (206/216 .447 .447 112), that should be good for mid-low 14's. I've got 150 extra HP in a little blue bottle in back. Hopeing for a possible 12.99 run with that.
I'm now running a single plane intake, with an UltraDyne cam (206/216 .447 .447 112), that should be good for mid-low 14's. I've got 150 extra HP in a little blue bottle in back. Hopeing for a possible 12.99 run with that.
Re: Everyone in! 1/4 mile times and cheap parts
Well i dont know what this means but i beat an 85 IROC-z last night.
He set me out 1 and the smack. He would of set me out more but he didnt like the fact that i was running open headers. I did the biggest burn out and still spun all the way through 1st. i had about 4 cars on him by the time we crossed.
He doesnt have a slow car either he has the BF dragradials free mods, air foil, accel coil and some other small stuff. Nuthing to big but he has no weight reduction.
I Have my mods and no interior at all, seat, shifter and wheel.
Hes not a bad driver at all but we both spun and i managed to outrun him still.
He said he only spun midway through first but i didnt expect to beat him that bad.
He set me out 1 and the smack. He would of set me out more but he didnt like the fact that i was running open headers. I did the biggest burn out and still spun all the way through 1st. i had about 4 cars on him by the time we crossed.
He doesnt have a slow car either he has the BF dragradials free mods, air foil, accel coil and some other small stuff. Nuthing to big but he has no weight reduction.
I Have my mods and no interior at all, seat, shifter and wheel.
Hes not a bad driver at all but we both spun and i managed to outrun him still.
He said he only spun midway through first but i didnt expect to beat him that bad.
Thread
Thread Starter
Forum
Replies
Last Post
Hurin
Suspension, Chassis, and Brakes
4
Dec 13, 2014 07:38 PM



