swap items needed

I'm looking for 94 or 95 z engine wiring harness, crossmember, motor mounts, dual cooling fans, a good used radiator, fuel rails, drive shaft, gauge cluster, auto trans crossmember and mounts, accessory brackets, power steering resevoir, headers, aftermarket single cat exhaust and y pipe, and other assorted items. if you think you have anything i can use let me know. The swap is a 94 vette lt1 and vette 4l60e going into a 95 3.4l camaro.

thanks!

edit: I now have almost all of this stuff except for all heater and coolant hoses(only interested if they are in exceptional shape), oil pressure sensor (back top of the block), newer posi unit (I've got 3:23 gears), new or newer 3000 stall converter (preferably yank, vig, or fuddle), and new or newer shocks. I did this edit so you don't have to read through all of the posts.
thanks again

Im parting out a complete 97 trans am, all parts are 90k miles and the car was BABIED. Poor friend got t-boned.

The only thing I dont have is the exhaust. I can get some painted mid length headers with barely any miles, painted ORY, and a SLP loudmouth catback from a friend if you're interested though.

Best way to reach me is on AIM, JKFBody or JeffZ33

Where are you located? I have a driveshaft and a few other parts.

thanks guys, found some items but still need 94 or 95 gauge cluster, power steering resevoir, accessory brackets and engine harness.

I have a cluster out of 95 camaro that i am stripping. I have other interior parts if you need anything. Make offer + shipping.

Lonnie

found a harness

still need low mileage water pump, power steering pump, k-member, heater hoses, ac hoses, coolant hoses, lt leaders and y-pipe, catback exhaust (single cat), fuel rails ( if they are complete with all related lines, fuel pressure regulator, etc.) basically rails and everything located on the intake manifold, engine bay fuel lines. that's all I can think of now.

side note: I'm using a vette lt1- will camaro rail work with this set up?

Camaro and Corvette LT1 were almost identical except for the 4-bolt main. I have some shorty headers and y-pipe for sale cheap.

I have the fuel rails. They are complete and polished. $65 plus shipping or $100 plus shipping including injectors. Bill

I also have the engine bay fuel lines and the p/s reservoir if you still need them. Bill

I have the fuel rails. They are complete and polished. $65 plus shipping or $100 plus shipping including injectors. Bill

thanks for the reply, have gotten a few hits on the rails and fuel lines. I already got the resevoir, but if the other set of rails falls through I'll let you know.

Camaro and Corvette LT1 were almost identical except for the 4-bolt main. I have some shorty headers and y-pipe for sale cheap.

what year are they for? what manufacturer, and what kind of shape are they in (have they been modified or anything) coated or painted? Pics would be good.

thanks

where you located, I have a k-member and some other misc. stuff if you need it

what year are they for? what manufacturer, and what kind of shape are they in (have they been modified or anything) coated or painted? Pics would be good.

thanks

Check them out here.

http://web.camaross.com/forums/showthread.php?t=499924

thanks mdacton, one of the members is giving me a k-member and all I have to do is pay for shipping. if it doesn't happen I'll let you know.

thank you also seawolf06, I checked them out and although they are a great price, but they're not exactly what I'm looking for.

still need low mileage water pump, power steering pump, k-member, heater hoses, ac hoses, coolant hoses, lt leaders and y-pipe, catback exhaust (single cat), fuel rails ( if they are complete with all related lines, fuel pressure regulator, etc.) basically rails and everything located on the intake manifold, engine bay fuel lines. that's all I can think of now.

side note: I'm using a vette lt1- will camaro rail work with this set up?

Upate:

still need heater hoses, ac lines, coolant hoses, headers and y-pipe, catback, maf sensor, intake elbow (no vent hole for opti), front springs, shocks if they aren't that old, oil pan (94 or 95) preferrably w/ low oil sensor.

Keep em' coming fellas, You guys on this forum have been awesome! I almost have everything I need for my lt1 swap and I owe it all to the members of this forum, much thanks to everyone who has helped with parts and info.

Noah

I can help you on a pan and possibly those ac lines...

Upate:

still need heater hoses, ac lines, coolant hoses, headers and y-pipe, catback, maf sensor, intake elbow (no vent hole for opti), front springs, shocks if they aren't that old, oil pan (94 or 95) preferrably w/ low oil sensor.

Keep em' coming fellas, You guys on this forum have been awesome! I almost have everything I need for my lt1 swap and I owe it all to the members of this forum, much thanks to everyone who has helped with parts and info.

Noah

Another update/bump:

I have a few things pending, water pump, intake elbow and maf. I bought pacesetter lts and y pipe and will most likely be purchasing magnaflow within the next day or so.
So I'm down to a few things: coolant and heater hoses, springs, shocks, stock or aftermarket front sway bar, and I also need any other accesory brackets excluding the main accesory bracket (alternator rear bracket- just the little arm brace on the back, and also ac and ps rear brackets if they have them), good posi unit for 3:23's, I'm not sure if the crank pulley and harmonic balancer on the 94 vette motor I have are the same as f-body, so if someone knows that they are different, I'll need those too. Also need tensioner pulley and if anyone knows where to get an egr block off plate or has one for sale, let me know.

No longer need tensioner or alternator bracket/ found out I do need crank pulley/balancer
thanks again :bow:

I have the tensioner and the brace for the rear of the alternator. Maybe the a/c rear brace too. Bill

Another update/bump:

I have a few things pending, water pump, intake elbow and maf. I bought pacesetter lts and y pipe and will most likely be purchasing magnaflow within the next day or so.
So I'm down to a few things: coolant and heater hoses, springs, shocks, stock or aftermarket front sway bar, and I also need any other accesory brackets excluding the main accesory bracket (alternator rear bracket- just the little arm brace on the back, and also ac and ps rear brackets if they have them), good posi unit for 3:23's, I'm not sure if the crank pulley and harmonic balancer on the 94 vette motor I have are the same as f-body, so if someone knows that they are different, I'll need those too. Also need tensioner pulley and if anyone knows where to get an egr block off plate or has one for sale, let me know.

No longer need tensioner or alternator bracket/ found out I do need crank pulley/balancer
thanks again :bow:

Still need crank pulley/harmonic balancer, all heater/coolant hoses (including the coolant line that bolts to the back of the block in two places and runs between the intake manifold and valve cover up to the radiator), good deal on new or newer 3000 stall conv. I also need ignition coil, ignition control module, and all related mounting for these- including bolts. I was working on my motor today and realized that the corvette setup is on the wrong side and will be in the way of the camaro accesory bracket.

pending: front sway bar, springs, rear ac bracket, posi unit

thanks

still need fuel rails and etc

still need fuel rails and etc

Nope, I got those- thanks.

Still need crank pulley/harmonic balancer, all heater/coolant hoses (including the coolant line that bolts to the back of the block in two places and runs between the intake manifold and valve cover up to the radiator), good deal on new or newer 3000 stall conv. I also need ignition coil, ignition control module, and all related mounting for these- including bolts. I was working on my motor today and realized that the corvette setup is on the wrong side and will be in the way of the camaro accesory bracket.

pending: front sway bar, springs, rear ac bracket, posi unit

thanks

I have a stock crank pulley, ignition coil (you need 92-95 2 plug, or 96/97 1 plug?), ignition module. I don't have the bolts for that stuff though. I have a ton of parts here. You need anything else?

I have a stock crank pulley, ignition coil (you need 92-95 2 plug, or 96/97 1 plug?), ignition module. I don't have the bolts for that stuff though. I have a ton of parts here. You need anything else?

I ended up getting that stuff, thanks anyhow. All I need now are all heating and coolant hoses/lines (exceptional condition only), oil pressure sensor (top rear of engine block), new or newer shocks, posi unit (I've got stock 3:23 gears), new or newer 3000 stall converter-preferably a yank, vig, or fuddle, and I think thats about it.
thanks again to those who have contacted me about parts and also given me the information I've needed for this swap.

I ended up getting that stuff, thanks anyhow. All I need now are all heating and coolant hoses/lines (exceptional condition only), oil pressure sensor (top rear of engine block), new or newer shocks, posi unit (I've got stock 3:23 gears), new or newer 3000 stall converter-preferably a yank, vig, or fuddle, and I think thats about it.
thanks again to those who have contacted me about parts and also given me the information I've needed for this swap.

Ok, cool. I have the sensor.