tranny leak..

alright, i finally get me car going.. and now i have a bad tranny leak. well i took a shot and replaced the tranny pan gasket., well that was a no go. still leaking good!.
and its not leaking from the lines into the tranny itself.. but somewheres its leaking.
theres fluid on my y-pipe,(which burns up and smokes bad). and its on the starter!.. i cant seem to find the leak!. i thought it may be my front seal. but theres no fluid on the converter. well i donno, if anyone has any ideas as to what i can do to find out what it is. let me know!> thanks
shaun

------------------
1987 IROC-Z
355ci, Dart 2.02x1.60, compete forged bottom end, SLP siamesed runners, fully ported Edelbrock manifold and plenum, 58mm TB, Accel 26lb Injectors, Edelbrock headers & y-pipe, Flowmaster 3" cat-back, Rebuilt 700r4, B&M Megashifter, Holley 255lph fuel pump, triple guage pod, !A/C & Heat, !Smog pump, bypassed TB, MJS Ram air, custom PROM, Lakewood control lower control arms, Lakewood adjustable pan hard, Sub-Frames, Hotchkis Strut tower brace, Adjustable Torque Arm, 150hp NOS
IROC Pix (http://community.webshots.com/user/snksknrz28)

sounds like your pump seal.mone does it but not to bad unless i leave it in 2nd for a while

where is the pump seal? on the 700r4.
and i only see fluid on passenger side, and on the front of the pan...ill look at that though as soon as i find out what it looks like, and where it is. thanks.
later
shaun

------------------
1987 IROC-Z
355ci, Dart 2.02x1.60, compete forged bottom end, SLP siamesed runners, fully ported Edelbrock manifold and plenum, 58mm TB, Accel 26lb Injectors, Edelbrock headers & y-pipe, Flowmaster 3" cat-back, Rebuilt 700r4, B&M Megashifter, Holley 255lph fuel pump, triple guage pod, !A/C & Heat, !Smog pump, bypassed TB, MJS Ram air, custom PROM, Lakewood control lower control arms, Lakewood adjustable pan hard, Sub-Frames, Hotchkis Strut tower brace, Adjustable Torque Arm, 150hp NOS
IROC Pix (http://community.webshots.com/user/snksknrz28)

well i got the tranny out. and the front seal has no cracks or anything from what i can see.. i looked over the tranny and visually i cant seem to find where it would be coming from!. i guess monday or sometime during the week ill get it over to a shop and have them look at it.

pump seal is the piece with all the bolt around it (the TC seal is in it)

how much do you guys think it is going to cost me to have a place check it out, and re-gasket the tranny?
thanks guys.
and if it STILL leaks what should i replace next?..
later
shaun

------------------
1987 IROC-Z
355ci, Dart 2.02x1.60, compete forged bottom end, SLP siamesed runners, fully ported Edelbrock manifold and plenum, 58mm TB, Accel 26lb Injectors, Edelbrock headers & y-pipe, Flowmaster 3" cat-back, Rebuilt 700r4, B&M Megashifter, Holley 255lph fuel pump, triple guage pod, !A/C & Heat, !Smog pump, bypassed TB, MJS Ram air, custom PROM, Lakewood control lower control arms, Lakewood adjustable pan hard, Sub-Frames, Hotchkis Strut tower brace, Adjustable Torque Arm, 150hp NOS
IROC Pix (http://community.webshots.com/user/snksknrz28)