CamaroZ28.Com Message Board - Search Results

 
Search: Posts Made By: 442olds
Showing results 1 to 25 of 101
Search took 0.22 seconds.
12-12-2008, 10:59 PM
Replies: 5
Views: 452
Posted By 442olds

No codes, no water in the oil, no water coming...

No codes, no water in the oil, no water coming out the exhaust.
12-12-2008, 10:03 AM
Replies: 5
Views: 452
Posted By 442olds

Rough Startup

I have a 95 that is having problems starting. it takes several 10~15 second burst of the starter to get it to start, and when it does start, it slowly revs up, not the snapping starts I'm used to...
09-09-2008, 07:10 PM
Replies: 6
Views: 383
Posted By 442olds

Caps good and the "water" is good to -20F. I...

Caps good and the "water" is good to -20F. I always refer to it as water, bad habit I picked up from my mechanic father i guess. Any other suggestions.....

What about dirty injectors....like say...
09-09-2008, 05:42 PM
Replies: 6
Views: 383
Posted By 442olds

I'm open to the air in the system explanation,...

I'm open to the air in the system explanation, but on both heads at the lowest part of the head's water jacket, and this started recently. The system has been filled with water for sometime now. So...
09-09-2008, 01:51 PM
Replies: 6
Views: 383
Posted By 442olds

I'm talking in the gaps between 1/3 5/7 2/4 6/8,...

I'm talking in the gaps between 1/3 5/7 2/4 6/8, not 3/5 and 4/6. The same area where the temp sender goes in. I've never experienced this much of a temp difference on any of my previous small...
09-09-2008, 01:05 PM
Replies: 6
Views: 383
Posted By 442olds

cylinder heads are hot

Ok here's the situation. My temp gage (senders in the head) reads high, real high 230~250F. So I bought a new sender, same problem. So I get out he infrared temp gun and start poking around. The...
05-19-2008, 09:55 PM
Replies: 63
Views: 2,999
Posted By 442olds

Do you have the sunvisors and what condition are...

Do you have the sunvisors and what condition are they in?
05-19-2008, 09:50 PM
Replies: 54
Views: 2,650
Posted By 442olds

Hey what color is the interior and what shape are...

Hey what color is the interior and what shape are the sun visors in?
04-28-2005, 07:25 AM
Replies: 0
Views: 209
Posted By 442olds

FS: Camaro Hood and Spoiler Black

I have a stock hood and a spoiler from a Z-28 for sale. I can supply pictures upon request. The Hood could use a repaint as the paint on it is starting to spider crack. The spoiler also has some...
03-03-2005, 02:38 PM
Replies: 86
Views: 4,755
Posted By 442olds

Re: parting out '98 Camaro SS

How bout the ss badges from the front fenders and rear bumper??
01-25-2005, 01:37 PM
Replies: 6
Views: 547
Posted By 442olds

Re: Proform 1.6 rockers

I have had mine for a couple years now, no major issues. One recomendation would be to install new studs. The factory studs are a little short and you won't have a whole lot of thread engagement...
01-08-2005, 12:25 AM
Replies: 1
Views: 281
Posted By 442olds

Re: Impala head gaskets

On the head gaskets look at the water ports in the block. I think it should only line up good one way. I can't really remember which way I put them down. they should seal either way as long as all...
12-21-2004, 11:21 PM
Replies: 5
Views: 436
Posted By 442olds

Re: Help on compression ratio

I assumed the gasket diameter was 4.060 not the block diameter, I also guessed on the gasket thickness, but your not going to see that much of a change in cr with the difference in either dimension....
12-20-2004, 10:13 PM
Replies: 5
Views: 436
Posted By 442olds

Re: Help on compression ratio

Assuming these numbers here's your compression ratios. KB has two dcup pistons one 18 cc and one 28cc and I have it calculated for both for ya there.

Bore = 4.030
Stroke = 3.75
Rod Length = 5.7...
12-20-2004, 09:32 PM
Replies: 1
Views: 312
Posted By 442olds

Re: Need help with Breslin bolts

make sure you back out the small locking set screw so that the bolt returns to its stanard size.

buy a 12 point wrench and grind as needed.
12-16-2004, 12:49 PM
Replies: 4
Views: 531
Posted By 442olds

Re: Why are earlier LT1 timing sets cheaper than 95+?

The stock chain and lower sproket is the same chain that GM has used in every small block since probably the creation of the small block. Its an ok chain it does stretch a bit but I've see double...
12-13-2004, 02:40 PM
Replies: 16
Views: 1,348
Posted By 442olds

Re: is everyone else tired of the hit or miss luck with adjusting valves?

get poly locks, its so simple. Just trun till you feel resitanceon the poly lock, that's zero ( and yes you can continue to turn the poly lock after it starts to compress the lifter but when you...
12-05-2004, 12:57 AM
Replies: 15
Views: 1,414
Posted By 442olds

Re: ARP main stud/widage tray?

I drilled out the holes in question to about 7/8" and then I turned some spacers on my lathe that would accept the correct socket for the arp windage tray nuts. Weld the spacers to the windage tray...
11-27-2004, 11:34 AM
Replies: 4
Views: 455
Posted By 442olds

Re: Rusted Front Sturt Need Part #'s

THanks for the help.

1 Question: If they are truely coil over shocks then why does my service manual and the auto parts store list them as struts? I was always under the impression that it was...
11-27-2004, 09:26 AM
Replies: 4
Views: 455
Posted By 442olds

Unhappy Rusted Front Sturt Need Part #'s

Well I have a 150,000 miles on the orginal sturts and felt it was time to replace them. It wasn't floating or anything but man 150,000 miles on factory sturst just seemed way to long. So last night...
09-09-2004, 08:48 AM
Replies: 0
Views: 294
Posted By 442olds

Computer won't chat with car

I have a 93 z akm cable and free scan for software. I can get freescan to force the data out of the car, so I know it can make a connection and talk to the car but the two don't want to play togther...
08-30-2004, 09:00 AM
Replies: 1
Views: 248
Posted By 442olds

Window switch ?

Does anyone know if the passenger side window switch is broken on the drivers side switch panel, should the passnger side switch still roll down the window?
08-19-2004, 07:18 AM
Replies: 2
Views: 198
Posted By 442olds

Re: A few more piston ?

The only real difference is how much volume the valve reliefs have. 2vr will have less volume and there fore your compression ratio will be a little higher. The 4vr piston can be used in any hole...
Forum: Advanced Tech
08-11-2004, 11:07 AM
Replies: 12
Views: 1,087
Posted By 442olds

Re: Formula to figuring out Compression Ratio?

http://www.et-motorsports.cc/tech/engine_build_sheet.xls

This spreadsheet will calculate it for you. Just fill in the information denoted by the yellow boxes.
07-21-2004, 11:13 AM
Replies: 13
Views: 1,135
Posted By 442olds

Re: New LT1 rebuild running hot

What fuel injectors are you running. If you haven't upgraded the fuel injectors yet and are running stock programming for the 350, there is a good chance your running lean enough to overheat. I had...
Showing results 1 to 25 of 101
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.