CamaroZ28.Com Message Board - Search Results

 
Search: Posts Made By: lt1-xjs
Showing results 1 to 25 of 416
Search took 0.19 seconds.
07-20-2018, 03:56 PM
Replies: 16
Views: 1,738
Posted By lt1-xjs

Re: No coolant flow LT1

Get the AutoZone loan a tool block tester. You'll have to spend $10 for the test fluid.
07-16-2018, 08:06 AM
Replies: 16
Views: 1,738
Posted By lt1-xjs

Re: No coolant flow LT1

https://www.camaroz28.com/forums/lt1-based-engine-tech-9/1995-lt1-engine-cooling-line-routing-881977/ Look at post 6 for the diagram and post 10 for the routing. If your filler neck is the highest...
07-11-2018, 10:18 AM
Replies: 16
Views: 1,738
Posted By lt1-xjs

Re: No coolant flow LT1

A little more info is needed, motor year, type of radiator, how the heater hoses and steam line are connected. Some ports will need plugged.
05-31-2018, 09:38 AM
Replies: 6
Views: 478
Posted By lt1-xjs

Re: How you tell when the torque converter locks up?

Just start from a dead stop under moderate throttle it should shift 4x by like 50 mph. 1,2,3 & lockup.
05-20-2018, 05:51 PM
Replies: 6
Views: 441
Posted By lt1-xjs

Re: understanding guideplates

You do not use guide plates with S/A rockers.
03-05-2018, 06:49 PM
Replies: 43
Views: 9,860
Posted By lt1-xjs

Re: lt4 hot cam questions

The Howards 98215 is a drop in spring, leave the damper out.
03-01-2018, 03:38 PM
Replies: 6
Views: 550
Posted By lt1-xjs

Re: Header modify???

You'll need a set of collector reducers. Do those have 02 bungs ? Flowtech 10004: Exhaust Reducer 3-Bolt 3" Collecter Flange Inlet | JEGS...
01-13-2018, 02:17 PM
Replies: 6
Views: 849
Posted By lt1-xjs

Re: Which vacuum hose is this?

Pull it off and cut the ends back 1/2", reinstall and see if it's tight.
12-25-2017, 02:53 PM
Replies: 5
Views: 427
Posted By lt1-xjs

Re: Cam requirements

After your cam selection you will need a tune. Fill out the custom spec sheet in detail, any questions call Alvin. Mail Order Tuning ? PCM of NC, Inc....
11-23-2017, 10:34 AM
Replies: 1
Views: 474
Posted By lt1-xjs

10-26-2017, 07:05 PM
Replies: 4
Views: 385
Posted By lt1-xjs

Re: 93 questions

The are low being stock, adjust the t/v cable. I set mine for max pressure. Remove the cover by the, 1 screw at the throttle body. Find the lock button where the cable goes in and mark the cable so...
10-25-2017, 06:46 PM
Replies: 4
Views: 385
Posted By lt1-xjs

Re: 93 questions

1. It appears the fuel rails would fit from 1993 to 1994
2. The 1993 throttle body is vehicle specific as Injuneer said. I have a new in the box BBK 1540 52mm I'll give you a deal.
3. The '93 4l60...
10-23-2017, 05:46 PM
Replies: 5
Views: 443
Posted By lt1-xjs

Re: What valve springs do I need for 1.6 rockers?

Howards 98215 springs use the stock hardware, leave out the damper coil.
09-23-2017, 02:17 PM
Replies: 5
Views: 240
Posted By lt1-xjs

Re: sluggish cranking when hot

Have the battery load tested.
07-26-2017, 05:55 PM
Replies: 3
Views: 473
Posted By lt1-xjs

Re: Square port headers for LT1 Camaro

Post pics of the gasket on the head and on the Speed E header flange.
07-26-2017, 12:05 PM
Replies: 3
Views: 473
Posted By lt1-xjs

Re: Square port headers for LT1 Camaro

You need headers that fit the AFR heads. First determine which heads you have, the 195 will take the felpro 1404. The 210 or 227 takes the felpro 1405. Use the correct gasket for the head you have....
07-09-2017, 01:26 PM
Replies: 8
Views: 560
Posted By lt1-xjs

Re: Bolt on record

I have never seen anyone break 320 rwhp with out pulling the heads, at that point you are beyond bolt-ons.
06-05-2017, 12:02 PM
Replies: 21
Views: 2,240
Posted By lt1-xjs

Re: Correct Fuel Injectors?

That's a Bosch design 3 off a Ford, 19-22 # flow. 0 280 155 710 should be on the other side, 0 280 155 700 is the 19 #.
06-03-2017, 05:06 PM
Replies: 3
Views: 474
Posted By lt1-xjs

Re: Is 20w 50 safe

Factory fill on the Corvette was 5w30 Mobil one. That's good enough for me.
03-05-2017, 12:36 PM
Replies: 2
Views: 496
Posted By lt1-xjs

Re: 96 SS. Good price??

Some are asking way more money for higher mileage cars. Yours is a very low mile car. Do your research. Year: 1996 : The Official SLP Registry (http://www.slpregistry.com/year/1996.html)
02-18-2017, 06:05 PM
Replies: 10
Views: 2,148
Posted By lt1-xjs

Re: 93 LT1 Plug Wire help

I used the 32143 MSD wires. Ran the wires from underneath and pulled them in close to the block with wire ties. No issues and you can't see them.
2167

2168
01-21-2017, 02:40 PM
Replies: 7
Views: 450
Posted By lt1-xjs

Re: 1993 z28 crank replacement

I'd reuse the stock rod, install ARP bolts and have it resized.
01-19-2017, 03:21 PM
Replies: 7
Views: 450
Posted By lt1-xjs

Re: 1993 z28 crank replacement

The crank may be able to be cleaned up and reused.
11-02-2016, 09:43 AM
Replies: 9
Views: 696
Posted By lt1-xjs

Re: LT1 Heads

All the heads will interchange and in stock form flow about the same. The early 374 and 643 castings are more desirable for porting.
10-14-2016, 03:56 PM
Replies: 11
Views: 2,057
Posted By lt1-xjs

Re: 1995 LT-1 Question

As stated there is no need to run the line through the throttle body. Run the line from the rear of the heads to the tee you are getting and mount it in the return line to the radiator.
Showing results 1 to 25 of 416
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.