CamaroZ28.Com Message Board - Search Results

Search: Posts Made By: 2FastZeder
Showing results 1 to 21 of 21
Search took 0.00 seconds.
09-03-2018, 10:47 PM
Replies: 6
Views: 260
Posted By 2FastZeder

Re: LS1 lifters fit into LT1?

Thanks for all the info guys.
I purchased a set of 850s from summit for $175.00 with my discount. Regular 199.00 better than the $250 for Howards.

Are the 850s also zero lash to 1/8 turn. ...
09-03-2018, 03:13 PM
Replies: 6
Views: 260
Posted By 2FastZeder

Re: LS1 lifters fit into LT1?

Thanks for the reply.
The very first lifters I wanted to go with was the 850s but I heard a lot of bad rap on those on this website. So now Im confused. You have a lot of miles on yours with no...
09-03-2018, 07:47 AM
Replies: 6
Views: 260
Posted By 2FastZeder

LS1 lifters fit into LT1?

Im building a 396 stroker LT1 and am planning on using the Howards Cams 91174 Variable Valve timing LS1 lifters.

Will the LS1 lifters work in the LT1 engine?
The diameter seems the same.
I...
08-06-2018, 01:39 PM
Replies: 11
Views: 326
Posted By 2FastZeder

Re: LT1 Rear Main Cap Oil Gally Check Ball Pressed In???

Ya I cut the rod I was using down some and the ball finally came out.
I would have assembled a good portion today if I had assembly lube, holiday today in Canada prevented me from that.
Thanks
08-05-2018, 07:11 AM
Replies: 11
Views: 326
Posted By 2FastZeder

Re: LT1 Rear Main Cap Oil Gally Check Ball Pressed In???

Thanks for the compliment.
Im kinda on a beer budget on this project, so I got OK parts not top of the line but not cast junk either.
EAGLE forged 3.875 stroke crank
EAGLE forged 6.0 rods ARP...
08-04-2018, 09:28 PM
Replies: 11
Views: 326
Posted By 2FastZeder

Re: LT1 Rear Main Cap Oil Gally Check Ball Pressed In???

Thanks for all the input guys.
As you can see the block is all machined, clearanced for a 396 and cleaned so I did tap from the right end as I mentioned. The threaded rod I used to tap it with was...
08-04-2018, 02:39 PM
Replies: 11
Views: 326
Posted By 2FastZeder

Re: LT1 Rear Main Cap Oil Gally Check Ball Pressed In???

I already tried that.
If I do get it out am I suppose to drive it in again or drop it in like the manuals say?
08-03-2018, 06:27 PM
Replies: 11
Views: 326
Posted By 2FastZeder

LT1 Rear Main Cap Oil Gally Check Ball Pressed In???

I'm working on a 94 LT1 with low miles and I believe its all factory stock never rebuilt from what I know. And I tried getting the ball out from underneath the rear main cap but it won't come out I...
09-28-2017, 09:20 AM
Replies: 15
Views: 413
Posted By 2FastZeder

Re: 396 compression ratio? Tried many calcs. Dif. Answers

Here in Canada Peto Canada Bought out Sunoco and still selsl ULTRA 94 Octane
and still painted yellow and red at the pump selection lol also a few other gas stations too...lol
09-27-2017, 07:09 PM
Replies: 15
Views: 413
Posted By 2FastZeder

Re: 396 compression ratio? Tried many calcs. Dif. Answers

So at 94 Octane, I should not experience retard issues?
09-27-2017, 07:08 PM
Replies: 15
Views: 413
Posted By 2FastZeder

Re: 396 compression ratio? Tried many calcs. Dif. Answers

WOW Again Thanks, A lot FRED
I got a 160' thermostat and engaged the fans earlier.
I got a Moroso CAI kit
12.5 A/F Ratio target
Spark retarded due to nitrous but off nitrous not sure yet
Spark...
09-27-2017, 10:23 AM
Replies: 15
Views: 413
Posted By 2FastZeder

Thumbs up Re: 396 compression ratio? Tried many calcs. Dif. Answers

OK according to the Wallace Racing Calculator I have a DCR of 8.59:1 HOW much Octane Can I run would I be safe at 94 Octane before the computer retards it?
"INJUNEER" you were right it was kinda...
09-27-2017, 10:01 AM
Replies: 15
Views: 413
Posted By 2FastZeder

Re: 396 compression ratio? Tried many calcs. Dif. Answers

WOW at 45,000 posts you do your homework!!!

I did not notice the .050 and .006 lift so I'm off again [email protected]$&!

Why is this so hard last time the machine shop guaranteed mee the results and I came...
09-26-2017, 11:58 AM
Replies: 15
Views: 413
Posted By 2FastZeder

Re: 396 compression ratio? Tried many calcs. Dif. Answers

OK i'm getting the right answers now.

STATIC COMPRESSION RATIO 11.244

DYNAMIC EFFECTIVE COMPRESSION RATIO 7.498

NOW HOW HIGH OCTANE DO I NEED???

THANKS
09-26-2017, 11:28 AM
Replies: 15
Views: 413
Posted By 2FastZeder

Re: 396 compression ratio? Tried many calcs. Dif. Answers

This is a different engine, the last engine your referring to is a 350 this is a stroker 395. The head has been milled a little over 1.25mm.

I'm just wondering how much octane will I need to run...
09-26-2017, 10:31 AM
Replies: 15
Views: 413
Posted By 2FastZeder

Re: 396 compression ratio? Tried many calcs. Dif. Answers

I was adding minus "-" in front of dished piston relief volume without it the numbers are more accurate not the same but close. I don't know what I'm punching in the wrong?

what the highest ratio...
09-26-2017, 10:14 AM
Replies: 15
Views: 413
Posted By 2FastZeder

Re: 396 compression ratio? Tried many calcs. Dif. Answers

I tried that calculator at .041 gasket thickness and it came out to 17.84????
09-26-2017, 10:09 AM
Replies: 15
Views: 413
Posted By 2FastZeder

Re: 396 compression ratio? Tried many calcs. Dif. Answers

Well, that sucks when I bought the parts it was supposed to be around 10.75-1

The highest octane gas I got to run on at the pump is 94 octane.

what would the compression be if I put in a .041...
09-25-2017, 10:09 AM
Replies: 15
Views: 413
Posted By 2FastZeder

396 compression ratio? Tried many calcs. Dif. Answers

Hello
And great forum
I've been trying to find out the SCR and DCR for my engine but every damb online calculator gives me a different answer.
Can some one help my specs are.


Cylinder Head...
11-05-2016, 08:36 PM
Replies: 4
Views: 464
Posted By 2FastZeder

Re: Milled Head Whats My Compression Now?

I have only taken out about 1cc out of the chambers. I'm pretty sure I still would have an increase in compression.
11-04-2016, 07:26 PM
Replies: 4
Views: 464
Posted By 2FastZeder

Milled Head Whats My Compression Now?

Hello Everyone

I'm currently rebuilding my LT1 and ported and polished the heads and milled them 1/2 a mm .020 thou
Can someone tell me what my static compression ratio now?

Thanks in advance.
Showing results 1 to 21 of 21


 
Forum Jump