CamaroZ28.Com Message Board - Search Results

Search: Posts Made By: ADOR
Showing results 1 to 23 of 23
Search took 0.00 seconds.
08-18-2018, 10:14 PM
Replies: 2
Views: 163
Posted By ADOR

Re: L33 with 4l80e

The 4l80e could be put behind the 4.3, 4.8 or 5.3 in vans from the factory in the 2500 and 3500 series work horse vans. Seen a couple of the 4.8/4l8oe stock setups and read about several more combos....
08-08-2018, 11:59 AM
Replies: 2
Views: 163
Posted By ADOR

L33 with 4l80e

This weekend or next week I should be getting a L33 or other Aluminum 5.3. For my project. (99 Camaro v6 to v8 swap) As long as the 4l80e is from behind a 4.8, 5.3 or 6.0 to my understanding all I...
04-03-2018, 11:15 PM
Replies: 5
Views: 641
Posted By ADOR

Re: 4th Gen Camaro distributor to fire wall clearance

The engine is a gen 1 SBC.The car is a 99 camaro. Still researching and deciding what parts to get and use. Hope to get he cam swapped into it and the heads swapped this time home. Even if I decide...
04-01-2018, 11:38 PM
Replies: 5
Views: 641
Posted By ADOR

4th Gen Camaro distributor to fire wall clearance

I was looking for some good pictures or someone else who had done it opinion. I have several aftermarket and stock distributors on hand to choose from. Would a smaller diameter but regular height...
03-04-2018, 09:36 AM
Replies: 2
Views: 392
Posted By ADOR

Re: V6 PCM for monitoring/gauges only

Thanks for the info. I knew the sensors on the engine pulled the info but wasn't sure if it went through the PCM or went directly to the gauges.

I have a older (1978 4bolt from a 3/4 ton van) two...
03-03-2018, 01:36 PM
Replies: 2
Views: 392
Posted By ADOR

V6 PCM for monitoring/gauges only

(Factory 1999 camaro with factory (dead/MIA)v6/t5(have) going to v8. Have sbc but if the deal goes though I will pick up a lsx. )

I am working on the final decisions on the SBC before I turn on a...
09-15-2017, 11:08 AM
Replies: 7
Views: 417
Posted By ADOR

Re: Starting a 99 Camaro Project

While looking over everything over while away at work I researched everything needed to narrow my search down. This is what I am down too.

For induction:

Torker 2 intake manifold (not the...
08-25-2017, 09:07 PM
Replies: 7
Views: 417
Posted By ADOR

Re: Starting a 99 Camaro Project

decided to add the Baby LT1 4.3 "265 CID" engine with 5 speed as a option as well. Still a 8 with less torque so the T5 may live behind it.

Measured my TH350 today and it's the 9" tail shaft...
08-20-2017, 12:59 PM
Replies: 18
Views: 1,029
Posted By ADOR

Re: Goodbye, old friend

Sounds strange they "sold" it before the final paper work was done. It's not technically their's until they pay for it. At least you did get a good price for it.
08-19-2017, 06:42 PM
Replies: 7
Views: 417
Posted By ADOR

Re: Starting a 99 Camaro Project

Found out more differences in the brakes on the rear end, etc. If I wind up swapping that. Right now looking over the pro / cons of these combos and looking at the differences in the wiring harness...
08-15-2017, 02:54 PM
Replies: 7
Views: 417
Posted By ADOR

Re: Starting a 99 Camaro Project

Thank you all that have replied. Still got more research to do and will be looking though the manuals link in the next few days for what I need.


I confirmed the brakes are still stock. Have...
08-13-2017, 08:57 PM
Replies: 7
Views: 417
Posted By ADOR

Starting a 99 Camaro Project

Now that the sons 93 Z28 is finally on the road and problem free after a long line of problems I have got back to messing with my projects. I have finally decided to let go of my 55 Chevy 150 sedan. ...
08-12-2017, 11:01 AM
Replies: 18
Views: 1,029
Posted By ADOR

Re: Goodbye, old friend

I still have nightmares from driving one of my cars to work while in high school. I spent months on my back with a grinder working under the car, replacing floor plates and a lot of stuff like that...
06-28-2017, 10:58 AM
Replies: 3
Views: 624
Posted By ADOR

Re: 1993 Z28 Engine Replacement

Finally found out some of the problems on this car, and working on sorting out the last details before handing over the keys to my oldest boy. The speedometer not working turned out the drive gear on...
01-23-2017, 01:31 PM
Replies: 10
Views: 742
Posted By ADOR

Re: Snapped Drive shaft whaa whaaa whaaaa

I see the three rivers sticker on it from what I have read that should be the stock drive shaft.
01-21-2017, 02:16 PM
Replies: 7
Views: 410
Posted By ADOR

Re: 1993 z28 crank replacement

Thank you all for your replies. I know I won't know for sure until I get time to tear it down in another month or two. Just preparing for the worse and wanted to double check the info I have read.
...
01-19-2017, 01:25 PM
Replies: 7
Views: 410
Posted By ADOR

1993 z28 crank replacement

After finally getting the right transmission installed and working in my oldest boys 1993 Z28 we cranked the engine for the first time and noticed it had a light tap on the passenger side. We thought...
11-06-2016, 08:41 PM
Replies: 3
Views: 624
Posted By ADOR

Re: 1993 Z28 Engine Replacement

It sounds like a very good educated guess. This car will be fixed, just trying to decide the best course of action before we even pull the engine. I figured it would be best to swap in all the...
11-05-2016, 10:43 PM
Replies: 3
Views: 624
Posted By ADOR

1993 Z28 Engine Replacement

After getting the trans sorted, 3" exhaust fixed, etc. The light tap we first heard from the engine has increased in noise. At first we thought it was just a lifter from it sitting up for awhile but...
Forum: Drivetrain
07-08-2016, 08:05 PM
Replies: 0
Views: 457
Posted By ADOR

1993 Z28 TV cable length from the factory

I am working on finishing up the work Me and my Father have been doing on my oldest son's Z28. The car was purchased with out trans, converter or TV cable. We have gotten a new replacement trans, got...
01-18-2016, 04:54 PM
Replies: 4
Views: 513
Posted By ADOR

Re: Another Z28

Thanks for the links. I will check it out.

I just want to make sure it will work before bolting the trans in. Got to look at the gear to speedometer sensor to see if it's the correct type for...
01-18-2016, 01:36 PM
Replies: 4
Views: 513
Posted By ADOR

Re: Another Z28

Around the thousand oak area
01-17-2016, 09:55 PM
Replies: 4
Views: 513
Posted By ADOR

Another Z28

Here reading up and trying to find everything I am looking for to help my 17 year old son with the 1993 Z28 he just purchased.

The car has already been upgraded with 17" alloy rims but that is...
Showing results 1 to 23 of 23


 
Forum Jump