performance parts 4 sale
#1
performance parts 4 sale
Hey Guys,
Well i am selling off everything, i have all the right parts here to make a 600-1000hp car all hi-end parts SO PLEASE NO LOW BALLERS
This is off my 95 T/A
I HAVE PICS OF EVERYTHING I WILL POST OR I CAN EMAIL THEM
Vortech Ysi, with Z8's brackets , with my custom 4" suck side and air filter
cog pulleys 36mm, 78 teeth crank/30 blower
8 rib pulleys 8" crank pulley with spacers/ 2.65 blower pulley with belt
FMIC and all the piping with extra clamps and hose
vortech mondo BOV
Alky control kit
singal kit & dual kit as well, with an extra pump $450
Nitrous Outlet elbow $275 for Vic intake
Vic Jr intake with fuel rails its fully ported and matched to the heads this stuff is a one off
matching AFR 220 heads
These are Z8's old AFR heads(220) that were ported by GTP that flow 330cfm@.600 and mating Vic intake you will not find another set of heads like this with shaft mounts 1.7r $3200.00
RACETRONIX / LONNIES PERFORMANCE Double Pumper kits - - Will support OVER 1000RWHP
$500 with the wiring kit from racetronix
upper/lower A arms BMR/Sphon $400 (new)
Qa1 for the front (newish) with 250lbs springs and shims $300
sphoon TQ arm $400
sphoon SFC CM $175 (new)
short block 355.....blower/nos set up
eagle rods 4340
eagle 4340
Je blower pistions
4 bolt main
balanced
ATi extra keyed crank
e-water
custom Bret B blower cam
Morrel's lifters
MAKE OFFERS ON ENG OR I CAN PART OUT
9" from DLS
35 spline axles
detroit locker
drive shaft for M6 tranny to match up with the 9" to handle 1000hp $2500.00
2 magnaflow cats new $150
borla cat back with adj plate $400
Canton LT1 Valve Covers $175 new
weld wheels
15x5 front with tires
15x10.5 with 7.5 bs and hoosher slicks $600
NEW MSD DIG 6 NEW 300.00
IF DOING PAYPAL ADD 3%
obo
Well i am selling off everything, i have all the right parts here to make a 600-1000hp car all hi-end parts SO PLEASE NO LOW BALLERS
This is off my 95 T/A
I HAVE PICS OF EVERYTHING I WILL POST OR I CAN EMAIL THEM
Vortech Ysi, with Z8's brackets , with my custom 4" suck side and air filter
cog pulleys 36mm, 78 teeth crank/30 blower
8 rib pulleys 8" crank pulley with spacers/ 2.65 blower pulley with belt
FMIC and all the piping with extra clamps and hose
vortech mondo BOV
Alky control kit
singal kit & dual kit as well, with an extra pump $450
Nitrous Outlet elbow $275 for Vic intake
Vic Jr intake with fuel rails its fully ported and matched to the heads this stuff is a one off
matching AFR 220 heads
These are Z8's old AFR heads(220) that were ported by GTP that flow 330cfm@.600 and mating Vic intake you will not find another set of heads like this with shaft mounts 1.7r $3200.00
RACETRONIX / LONNIES PERFORMANCE Double Pumper kits - - Will support OVER 1000RWHP
$500 with the wiring kit from racetronix
upper/lower A arms BMR/Sphon $400 (new)
Qa1 for the front (newish) with 250lbs springs and shims $300
sphoon TQ arm $400
sphoon SFC CM $175 (new)
short block 355.....blower/nos set up
eagle rods 4340
eagle 4340
Je blower pistions
4 bolt main
balanced
ATi extra keyed crank
e-water
custom Bret B blower cam
Morrel's lifters
MAKE OFFERS ON ENG OR I CAN PART OUT
9" from DLS
35 spline axles
detroit locker
drive shaft for M6 tranny to match up with the 9" to handle 1000hp $2500.00
2 magnaflow cats new $150
borla cat back with adj plate $400
Canton LT1 Valve Covers $175 new
weld wheels
15x5 front with tires
15x10.5 with 7.5 bs and hoosher slicks $600
NEW MSD DIG 6 NEW 300.00
IF DOING PAYPAL ADD 3%
obo
Last edited by Schurters LT1; 07-21-2008 at 10:57 PM.
#3
#12
ok ssssssooooo sorry about this...
tracking number
goto www.canadapost.ca
ca 234 997 475 ca
thanks
jeremy
tracking number
goto www.canadapost.ca
ca 234 997 475 ca
thanks
jeremy
#15