Miscl. Parts, cams, pistons, rods
Thread Starter
Registered User
Joined: Aug 2002
Posts: 489
From: Tulsa, OK
Miscl. Parts, cams, pistons, rods
I have a whole bunch of used parts but I'm sure someone will be interested in some.
The best parts are the solid roller cam and setup.
It's a GTP cam and I have specs on request. It's fairly large I will say. Barely streetable. I have springs and lifters that match. You'd just need retainers and locks.
I'd like to sell the set as a kit for 450.00. SOLD
But I may part it out if no one is interested.
I have a factory untouched black painted intake manifold... 50.00 SOLD
A set of Keith black Pistons 4.0 bore with factory rods attached. Make offer
A set of factory Pistons with better factory rods attached. Make offer
A factory '97 cam. Make offer SOLD
A bullet racing cam with super steep lobes... Have specs... 300.00
A one piece rear seal housing for crank. Make offer
Also a set of probe industries forged 5.7 rods with arp bolts never been used 300.00 (these are 600.00 new!) http://www.probeindustries.com/Probe...1204-10076.htm SOLD
A cast iron set of 4 bolt mains. Make offer
A factory 5.7 block, needs cleaned and checked. SOLD
This is all a collective bunch of parts that was going to be a 383 build for an s10.
However the truck is gone. And a SRT8 now sits in the garage. The dream of building another LT1 is gone. Ask any questions and I can send pics on request. PayPal is accepted and shipping charges are at cost of buyer. Or if a deal is agreed upon.
The best parts are the solid roller cam and setup.
It's a GTP cam and I have specs on request. It's fairly large I will say. Barely streetable. I have springs and lifters that match. You'd just need retainers and locks.
I'd like to sell the set as a kit for 450.00. SOLD
But I may part it out if no one is interested.
I have a factory untouched black painted intake manifold... 50.00 SOLD
A set of Keith black Pistons 4.0 bore with factory rods attached. Make offer
A set of factory Pistons with better factory rods attached. Make offer
A factory '97 cam. Make offer SOLD
A bullet racing cam with super steep lobes... Have specs... 300.00
A one piece rear seal housing for crank. Make offer
Also a set of probe industries forged 5.7 rods with arp bolts never been used 300.00 (these are 600.00 new!) http://www.probeindustries.com/Probe...1204-10076.htm SOLD
A cast iron set of 4 bolt mains. Make offer
A factory 5.7 block, needs cleaned and checked. SOLD
This is all a collective bunch of parts that was going to be a 383 build for an s10.
However the truck is gone. And a SRT8 now sits in the garage. The dream of building another LT1 is gone. Ask any questions and I can send pics on request. PayPal is accepted and shipping charges are at cost of buyer. Or if a deal is agreed upon.
Last edited by hosspwr94; Jul 5, 2016 at 12:26 PM.
too much mopar blood in you huh.
Thread Starter
Registered User
Joined: Aug 2002
Posts: 489
From: Tulsa, OK
Registered User
Joined: Jun 2000
Posts: 857
From: Washington, Michigan USA
Re: Miscl. Parts, cams, pistons, rods
I have a whole bunch of used parts but I'm sure someone will be interested in some.
The best parts are the solid roller cam and setup.
It's a GTP cam and I have specs on request. It's fairly large I will say. Barely streetable. I have springs and lifters that match. You'd just need retainers and locks.
I'd like to sell the set as a kit for 450.00.
But I may part it out if no one is interested.
I have a factory untouched black painted intake manifold... 50.00
A set of Keith black Pistons 4.0 bore with factory rods attached. Make offer
A set of factory Pistons with better factory rods attached. Make offer
A factory '97 cam. Make offer
A billet racing cam with super steep lobes... Have specs make offer
A one piece rear seal housing for crank. Make offer
Also a set of probe industries forged 5.7 rods with arp bolts 200.00
A cast iron set of 4 bolt mains. Make offer
A factory 5.7 block, needs cleaned and checked.
This is all a collective bunch of parts that was going to be a 383 build for an s10.
However the truck is gone. And a SRT8 now sits in the garage. The dream of building another LT1 is gone. Ask any questions and I can send pics on request. PayPal is accepted and shipping charges are at cost of buyer. Or if a deal is agreed upon.
The best parts are the solid roller cam and setup.
It's a GTP cam and I have specs on request. It's fairly large I will say. Barely streetable. I have springs and lifters that match. You'd just need retainers and locks.
I'd like to sell the set as a kit for 450.00.
But I may part it out if no one is interested.
I have a factory untouched black painted intake manifold... 50.00
A set of Keith black Pistons 4.0 bore with factory rods attached. Make offer
A set of factory Pistons with better factory rods attached. Make offer
A factory '97 cam. Make offer
A billet racing cam with super steep lobes... Have specs make offer
A one piece rear seal housing for crank. Make offer
Also a set of probe industries forged 5.7 rods with arp bolts 200.00
A cast iron set of 4 bolt mains. Make offer
A factory 5.7 block, needs cleaned and checked.
This is all a collective bunch of parts that was going to be a 383 build for an s10.
However the truck is gone. And a SRT8 now sits in the garage. The dream of building another LT1 is gone. Ask any questions and I can send pics on request. PayPal is accepted and shipping charges are at cost of buyer. Or if a deal is agreed upon.
Are these both solid roller LT1 cams?Thanks!
Thread Starter
Registered User
Joined: Aug 2002
Posts: 489
From: Tulsa, OK
Re: Miscl. Parts, cams, pistons, rods
everything is still available for your summer builds! lets make a deal and get this stuff out of my garage!
Also forgot to mention that I have a turbo 350 trans... 100.00 (needs to be gone through)
Also forgot to mention that I have a turbo 350 trans... 100.00 (needs to be gone through)
Thread Starter
Registered User
Joined: Aug 2002
Posts: 489
From: Tulsa, OK
Thread
Thread Starter
Forum
Replies
Last Post
carguyshu
Parts For Sale
20
Jan 22, 2017 11:19 AM