Car was built few months ago car was wrecked hit from the side. My friend's fault so he bought me a rolling chasis.

Car with new motor ran amazing. Had 373 gears with 315 tires and broke loose in 3rd gear. Pulled up to 6800 rpm and amazing low end torque and pulled on top like a rapped ape. Mild cam surge. Got 24 mpg on highway!

Now I want to put everything from the old car to new car but I got a job offer in the carribean and need the money and won't be here long. So if motor don't sell i'll put the car back together and sell the car running. If i do sell motor i will sell everything else tranny, rearend, rolling chasis and all other items. But a few parts i will sell now .

Motor: ( I have all receipts from shop that built the motor for everything done to the motor and parts) Lt1 97 block machined. Full motor. Ready to be put in. Only has 3203 miles on it barely broken. Dyno the car put down 410rwhp/430 rwtq. I have dyno sheet but misplaced it also head flow numbers when moved to new apt, will look for them. Dynoed at snyper performance in deland Florida, and heads flowed at express in deland , florida.

- 97 lt1 blue block, 11:8:1 compression ran great with 93 octane.Cloyes double roller timing chain. New meiling oil pump. New gm847 cam, .575/.595 on 112lsa. I have new intake gasket, mr gasket header gasket, water pump gasket,header bolts, 2 gallons of prestone coolant,throttle body gasket, 15 quarts of valvoline 10w30,3 gallons of mobile one syn 10w30 so you can switch to syn. oil when the motor is full broken in and two k&n oil filters i'll include.
-Eagle forged bottom end kit 383 4340 internal balanced all arp bolts. JE flat top -5 valve relief piston, Forge I beams rods
-lt1 alum stage II TEA ported heads, 274/225 at .600 3 angle valve job, arp head bolts, manley race valves stock size. Arp studs stock size, 1.6 RR Pro mag comp, comp springs double sprung up to .610 lift, Morel Lifters.
- Red lt1 intake ported matched to heads
- Brand new ac delco vented opti
- new march underdrive pulleys crank and alt
- new 58 mm bbk tb
- new ford motor racing 30lbs injectors
- Every sensor replaced
- new Lt1 corvette gear reduction starter
- new Meizeire electric water pump almost new only used for 3203 miles
- 95 lt1 pcm tuned for motor. m6 redline set at 7000rpm
- New 160 thermostat
- All pulleys, new belt tensioner, keyed hub,crane hi 6 coil. Have msd box 6a and have crane hi 6 off the car.
- Have all hoses and bolts for the motor.
- New poly ureth. motor mounts and tranny mount

-$4500(changed to $3500 now) without shipping Fully assembled motor with everything all you need is to put it in. I paid a little over 7k for this motor and machine shop and labor. Will take pics upon asked.

----------------------------------------------------------------

Tranny: 97 lt1 t56 stock around 35405 miles when I bought it so add 3203 miles i put on it. 3203 miles stage 3 ram power grip clutch stock neutral balanced flywheel.

-$800 shipping not calculated I paid $1100 for tranny and $500 for clutch.

-----------------------------------------------------------------
If i sell the motor i'll sell all of these parts and if the buyer doesn't want these parts with the motor

Parts:

- 3 " Alum drive shaft( $100) shipped
- Ford motor racing 30 lbs ($150) shipped
- Hooker long tubes,Brand new 02 sensors ($300)shipped
- Mufflex y pipe with a 3.5 " dyno max dump ($200) not shipped will take dump off if just want ypipe.
- March under drive pulleys crank and alt ($80 shipped)
- Almost new ac delco opti 95 vented $200
- bkk 58 mm tb with lt1 plate on top
- Almost new corvette gear reduction starter ($100)
- Poly urethane motor mounts in brackets ready to put on ($50) shipped
- Hurst t56 shifter ($80 shipped)
- t56 lt1 clutch ram power grip used for 3203 miles ($250) shipped
- ls1 strut tower brace red hotchkis the that bends back under dash ($50)
- Lt1 electric water pump meizere used only 3203 miles. ( $150) shipped
- Almost new 255 lph walboro fuel pump used only for 3203 miles ($50) shiped
- Brand new radiator never installed ($150) shipped
- 95 pcm m6 tuned for 30lbs injectors, 160 stat, fans come on early, everything delete from stock egr!, air pimp! skip shift! etc. ($100) shipped


--------------------------------------------------------
Misc. parts I will sell now.

-lt1 95 engine wiring harness a4 just missing oil level sensor. ($100 shipped)
- ls1 hotchkis red strut tower brace the one that bends back with 3 holes in middle ($50) shipped
-lt1 fuel rails with fuel pressure regulator on it ($40 shipped)
-New autozone a/c compressor for lt1 ($150) shipped
-t56 hurst shifter ($80) shipped
-a4 pedals ( $40) shipped
-m6 pedals ($40 )
-used 3203 miles 255 lph walboro fuel pump ($50) shipped
-lt1 ported maf ($50) shipped
-lt1 heater hose the expensive one the double heater hose that goes into firewall then back to waterpump ($50) shipped
-lt1 march underdrive pulleys crank and alt with almost new belt gatorback ($80) shipped
- lt1 a/c delete pulley and bracket ($40) shipped
- c5 conversation umi brake brackets with new reman left and right corvette calipers ($300) shipped Just the brackets are $200.
- Crane hi 6 ignition box with rev limiter ( $50) shipped
-93-97 fbody ttops both ($150) shiping not calculated

------------------------------------------------------------

94 quasar blue z28 with oem gm zr1 wheels on almost new tires 275/40/17 kumho rolling chassis ttops. Converted for m6 t56 pedals are in and hole cut for shifter. Fuel pressure gauge on it. Sub woofer and twp amps. Has an ls1 center console. Tinted limo all around. Rear left fender has small dent about 2" in diameter the rest nice shape small barely seen scratches. I can throw in a pioneer mp3 cd player.

Has a rebuilt 10 bolt rear end. All new seals, new precision 3.73 gears, with new torsen posi and new power stop cross drilled slotted rotors.

Engine bay in great shape with an msd 6a box, a/c compressor still in there,condensor and new radiator no installed yet. All wiring and 94 a4 pcm in there. Will throw in my 95 pcm flashed for m6/t56 tuned pcm if you like.

- Black leather interior
- Paint in great shape except spoiler and rear bumper clear coat gone.
- No rust at all.
- Have title
- Kept in garage

- Asking $1500

Everything is in daytona beach, Florida 32118. If you like I can deliver the rolling chassis for a small price.

Please email me at Arcedence1@aol.com or post here I will take pics of anything you like and like I said I have receipts for everything.

I will let this go for 1 week see how it goes then I will put everything together and sell the whole car for $7500

Thank you

Chris


Motor few weeks ago when it came from machine shop

 

great deal on the motor let me make some calls i'll pm you

 

I will buy the hotchkins strut tower brace if it is the right one that I am thinking it is.

Could you post up pics or send me a link to the right one on the internet?

Sent you pm also.

Troy

 

you dont have any cai's laying around by chance do you?

 

i do but i'll need it if i put the car back together i'll let you know

 

that's the bar i have the red one. My digital camera aint working i'll need to borrow my friends.

 

i'll take the strut tower brace if the other guy backs out

 

I'll definitely take the strut tower brace. Send me a pm with your paypal info and address. I'll get payment sent to you this weekend.

 

i'll let you know

 

Some excellent deals...wish u were close to IL..Id be all over that roller
free bump for ya

 

thanx

 

LT1/A4 harness is OBD2 correct?

 

How much for just the O2 sensors.

 

I'm interested in the fuel pump. Is it a stock drop in replacement? No need to modify anything?

 

it's an obd1 harness, i think the only difference is it doesn't have the rear o2 sensor pigtails