High end LT-1 parts
Thread Starter
Registered User
Joined: Dec 2003
Posts: 117
High end LT-1 parts
I am selling some parts I have off 94 LT-1. All are in good condition and have very little use.
ARP Headbolts, Felpro gaskets, LT-1 block bored .030 over- $250
Cam motion cam(Can find extact specs yet, will get em)Taller than LT4 Hot Cam
LT4 Ported intake- $175
LT4 rockers- $150 SOLD
Lunati Timing chain- $65
Moroso high polished valve covers- $150 SOLD
March underdrive pulleys- $75 SOLD
MSD Coil- $20
MSD 8mm wires- $75
MSD 6-btm ignition- $350
Ramchargers high flow water pump- $75
Adjutable fuel pressuer regulator- $100
Nitrous works wet kit- $400 SOLD
MSD boost retard controller- $125 SOLD
42# injectors- $300
Moroso 7 quart oil pan- $150
BBK 58mm throtle body- $225 SOLD
Ported MAF- $125
K&N Cold air intake- $125
Eagle 383 stroker kit
Brand new TPS sensor
Email or call 313-980-1428.
Steve
ARP Headbolts, Felpro gaskets, LT-1 block bored .030 over- $250
Cam motion cam(Can find extact specs yet, will get em)Taller than LT4 Hot Cam
LT4 Ported intake- $175
LT4 rockers- $150 SOLD
Lunati Timing chain- $65
Moroso high polished valve covers- $150 SOLD
March underdrive pulleys- $75 SOLD
MSD Coil- $20
MSD 8mm wires- $75
MSD 6-btm ignition- $350
Ramchargers high flow water pump- $75
Adjutable fuel pressuer regulator- $100
Nitrous works wet kit- $400 SOLD
MSD boost retard controller- $125 SOLD
42# injectors- $300
Moroso 7 quart oil pan- $150
BBK 58mm throtle body- $225 SOLD
Ported MAF- $125
K&N Cold air intake- $125
Eagle 383 stroker kit
Brand new TPS sensor
Email or call 313-980-1428.
Steve
Last edited by swasenko; Aug 21, 2005 at 08:39 AM.
Registered User
Joined: Jun 2002
Posts: 122
From: Peoria, IL, USA
Thread Starter
Registered User
Joined: Dec 2003
Posts: 117
Re: High end LT-1 parts
Swemdog:
The Eagle kit was installed and had some damage done to it after Firestone smacked my oil pan against a hoist and ran it without pressure. They paid for a new pan and that was it. The crank is bad but the rods and pistons look good. It was a forged kit with a reverse dome piston. Supposed to give 10.5 to 1 compression. I would want to get together with you since you are in the area and go over the stuuf to show you so there are no problems when you buy. Let's talk price, make an offer. Have you heard of Dyno Dave. He's a very good dyno guy in the metro area and his machinist did the work. I have his number if you like. Very top notch and ****.
Others:
The Moroso is a 7 quart side sump pan. I don't remember the exact model but it's the only one they make that's a 7 quart side sump for an LT-1.
Valve cover are like new and I will work on getting pics. Trust me they are clean.
The Eagle kit was installed and had some damage done to it after Firestone smacked my oil pan against a hoist and ran it without pressure. They paid for a new pan and that was it. The crank is bad but the rods and pistons look good. It was a forged kit with a reverse dome piston. Supposed to give 10.5 to 1 compression. I would want to get together with you since you are in the area and go over the stuuf to show you so there are no problems when you buy. Let's talk price, make an offer. Have you heard of Dyno Dave. He's a very good dyno guy in the metro area and his machinist did the work. I have his number if you like. Very top notch and ****.
Others:
The Moroso is a 7 quart side sump pan. I don't remember the exact model but it's the only one they make that's a 7 quart side sump for an LT-1.
Valve cover are like new and I will work on getting pics. Trust me they are clean.
Registered User
Joined: Sep 2003
Posts: 5,907
From: The Wild West
Re: High end LT-1 parts
I am interested in the Nitrous Works Kit. Is it complete and do you have pics? Ladiesman@cutey.com Is it the LT1 plate kit? Do you have any other supporting parts? Please list what all you are including with it. Also where are you located and how much for shipping?
-Dustin-
-Dustin-
Re: High end LT-1 parts
Thread Starter
Registered User
Joined: Dec 2003
Posts: 117
Re: High end LT-1 parts
FifeDogg:
I'll do $320 shipped. I can have pics tomorrow.
Bersaglieri:
It's the complete kit. It's not a plate, the nozzels are tapped into the intake elbow. I have a MSD Boost retard that I would like another $125 for. I cam get pics on it tomorrow. Shipping I would think would be about $30. I would have to see forsure, but I don't try to make anything on shipping.
I'll do $320 shipped. I can have pics tomorrow.
Bersaglieri:
It's the complete kit. It's not a plate, the nozzels are tapped into the intake elbow. I have a MSD Boost retard that I would like another $125 for. I cam get pics on it tomorrow. Shipping I would think would be about $30. I would have to see forsure, but I don't try to make anything on shipping.
Registered User
Joined: Jun 2005
Posts: 1,834
From: Indiana
Re: High end LT-1 parts
Im interested in the LT4 rockers, what ratio are they? Are they 1.6 and self allining? If so I want them! I will take them asap!
On a side note, will they fit in the LT1 valve covers?
Thanks,
Jason
On a side note, will they fit in the LT1 valve covers?
Thanks,
Jason
Registered User
Joined: Sep 2003
Posts: 5,907
From: The Wild West
Re: High end LT-1 parts
Originally Posted by Jazsun
Im interested in the LT4 rockers, what ratio are they? Are they 1.6 and self allining? If so I want them! I will take them asap!
On a side note, will they fit in the LT1 valve covers?
Thanks,
Jason
On a side note, will they fit in the LT1 valve covers?
Thanks,
Jason
-Dustin-