[Texas] Parting out car. LOTs of stuff available
#1
FS: built lt1 short block, t56, turbo parts, lt1 parts, rims, and more...
*** pictures uploaded to flickr available here: http://www.flickr.com/photos/60433308@N00/sets/
1996 firebird roller.sold
17x10" speed line rims. 2 with new nitto 555's. $600
like the part but not the price? pm me an offer.
master power t70 turbo .68 a/r new never used $500
Tial 38mm waste gate 3psi spring new never used $200
inter cooler 3x18x12" 3" in/out $150
2 Slim profile 10" fans $30each
Innovate SSI-4 $90 (no cd and missing terminator plug)
Innovate LC-1 wideband with serial to usb adapter $140
MSD timing retard p/n 8680 (for lt1) $100
MSD 2 step p/n 8739 with potentiometers "pills" (for lt1) $50
Autometer 5" 8000 rpm tach with shift light $100
Dennys nitrous ready drive shaft with 1350 u-joints $300
Strut tower brace. $60
AFR rev kit. $140
new shurflo 8000-643-210 pump $100
electric water pump with pump housing $140
comp cams pro magnum 3/8 stud non- self align 1.65:1 full roller rockers (p/n 1103-16) $250
comp cams hardened 7.200" pushrods $65
T56 Transmission $700 (lt1 style)
Master and slave cylinder $80
B&M shifter with hurst **** $120
adjustable panhard rod. $80 sold
tubular lower control arms. $70 sold
Eibach lowering springs and bilstien shocks less than 1000 miles. sold
Ported Trick flow heads. sold
PCM and harness sold
Brand new front runner 5 star rims with new tires sold
15x10 weld five star rims with brand new 27x10.5 et streets with tubes. sold
profab K-member for LT1 sold
Spec clutch with factory pressure plate low miles sold
Sphoon torque arm. sold
9" moser rear with 3.50 gears and tru trac diff. 31 spline 1350 yoke No abs. sold
Motor. Build by Mike Bernard in Axtell. Same builder who built Tony Shepherds motor (http://www.ls1tech.com/forums/member.php?u=7808) Built for turbo setup which is not available. est 1000 miles tuning and cruising never seen dyno or track.
383 LT1 short block $2600
-1/2 filled block. clearanced for 396. all rough edges grinded down
-compstar crank and rods JE -33cc dished pistons.
-decked and O-ringed
-8.4:1 compression with .050 copper head gaskets
-oliver billet main caps (all 5, middle three splayed four bolt)
-Melling high volume oil pump
-larger moroso oil pan
-Mild turbo cam. Cannot remember specs...230ish dur and .560 ish lift 114 LS? factory hydraulic lifters.
All parts are located in Waco Texas. Can work out arrangements for delivery within 100ish miles for parts. If shipping is required thats extra.
PM or email me for more pics/details or if you have any questions
1996 firebird roller.sold
17x10" speed line rims. 2 with new nitto 555's. $600
like the part but not the price? pm me an offer.
master power t70 turbo .68 a/r new never used $500
Tial 38mm waste gate 3psi spring new never used $200
inter cooler 3x18x12" 3" in/out $150
2 Slim profile 10" fans $30each
Innovate SSI-4 $90 (no cd and missing terminator plug)
Innovate LC-1 wideband with serial to usb adapter $140
MSD timing retard p/n 8680 (for lt1) $100
MSD 2 step p/n 8739 with potentiometers "pills" (for lt1) $50
Autometer 5" 8000 rpm tach with shift light $100
Dennys nitrous ready drive shaft with 1350 u-joints $300
Strut tower brace. $60
AFR rev kit. $140
new shurflo 8000-643-210 pump $100
electric water pump with pump housing $140
comp cams pro magnum 3/8 stud non- self align 1.65:1 full roller rockers (p/n 1103-16) $250
comp cams hardened 7.200" pushrods $65
T56 Transmission $700 (lt1 style)
Master and slave cylinder $80
B&M shifter with hurst **** $120
adjustable panhard rod. $80 sold
tubular lower control arms. $70 sold
Eibach lowering springs and bilstien shocks less than 1000 miles. sold
Ported Trick flow heads. sold
PCM and harness sold
Brand new front runner 5 star rims with new tires sold
15x10 weld five star rims with brand new 27x10.5 et streets with tubes. sold
profab K-member for LT1 sold
Spec clutch with factory pressure plate low miles sold
Sphoon torque arm. sold
9" moser rear with 3.50 gears and tru trac diff. 31 spline 1350 yoke No abs. sold
Motor. Build by Mike Bernard in Axtell. Same builder who built Tony Shepherds motor (http://www.ls1tech.com/forums/member.php?u=7808) Built for turbo setup which is not available. est 1000 miles tuning and cruising never seen dyno or track.
383 LT1 short block $2600
-1/2 filled block. clearanced for 396. all rough edges grinded down
-compstar crank and rods JE -33cc dished pistons.
-decked and O-ringed
-8.4:1 compression with .050 copper head gaskets
-oliver billet main caps (all 5, middle three splayed four bolt)
-Melling high volume oil pump
-larger moroso oil pan
-Mild turbo cam. Cannot remember specs...230ish dur and .560 ish lift 114 LS? factory hydraulic lifters.
All parts are located in Waco Texas. Can work out arrangements for delivery within 100ish miles for parts. If shipping is required thats extra.
PM or email me for more pics/details or if you have any questions
Last edited by S M R; 06-10-2010 at 06:07 PM. Reason: Update
#2
Got some pictures uploaded to flickr available here: http://www.flickr.com/photos/60433308@N00/sets/
Thread
Thread Starter
Forum
Replies
Last Post
dbusch22
Forced Induction
6
10-31-2016 11:09 AM