LT1 aftermarket and stock (McLeod, BeCool, LT1 heads, Prothane, etc...)
#1
LT1 aftermarket and stock (McLeod, BeCool, LT1 heads, Prothane, etc...)
-McLeod SFI bellhousing for LT1 F-bodies, very nice condition, includes the slave mount already installed mounted (assmebly required on new units). Ready to bolt on. All the proper hardware is included. One small area was clearance to clear my Kooks longtubes. SOLD
BeCool aluminum radiator for 93-02 F-body (M6 or A4), removed from my personal vehicle and in EXCELLENT condition, 3" thick, very low mileage (~5k). This is a direct bolt in with no modification required. I used this in my M6 car, but has the transmission cooler ports for automatics. The best radiator you can buy for these cars $750 new. $SOLD
-McLeod Street Twin discs (set of 2), brand new with zero miles. This is a custom friction material setup for holding high power levels without sacrificing any "streetability". Standard material on one side of the discs, the other side is Miba. SOLD
-Complete LT1 motor mounts with Prothane poly mounts for 93-97 F-body, mounted in LT1 clamshells, full upper and lower mounts for both sides, ready to bolt in with all of the hard work already done. This mounts are about as nice as "used" parts get. Clean, low mileage, no rust or corrosion on any of the metal. All nice "black" surfaces as they came new from GM. $80
-LT1 "643" castings, bare, no valves or springs, gasket matched ports on the intake side (no port work), needs a helicoil in one exhaust hole (helicoil installed, but protrudes above surface slightly). These would be great cores for porting as there is no other work done. $50/pr. SALE PENDING
-LT1 "643" heads, completely stock and assembled. These are about the nicest used LT1 stock heads I've seen. Resurfaced 2k miles ago with a skim cut (.005"). Very nice cores for porting or use as-is. $175/pr.
-LT1 intake manifold, painted black (very nice job), un-ported, includes very nice CNC TPIS AIR/EGR block off plates already mounted. $70
-LT1 fuel rails w/-AN fittings welded in and billet adjustable fuel pressure regulator. SOLD
BeCool aluminum radiator for 93-02 F-body (M6 or A4), removed from my personal vehicle and in EXCELLENT condition, 3" thick, very low mileage (~5k). This is a direct bolt in with no modification required. I used this in my M6 car, but has the transmission cooler ports for automatics. The best radiator you can buy for these cars $750 new. $SOLD
-McLeod Street Twin discs (set of 2), brand new with zero miles. This is a custom friction material setup for holding high power levels without sacrificing any "streetability". Standard material on one side of the discs, the other side is Miba. SOLD
-Complete LT1 motor mounts with Prothane poly mounts for 93-97 F-body, mounted in LT1 clamshells, full upper and lower mounts for both sides, ready to bolt in with all of the hard work already done. This mounts are about as nice as "used" parts get. Clean, low mileage, no rust or corrosion on any of the metal. All nice "black" surfaces as they came new from GM. $80
-LT1 "643" castings, bare, no valves or springs, gasket matched ports on the intake side (no port work), needs a helicoil in one exhaust hole (helicoil installed, but protrudes above surface slightly). These would be great cores for porting as there is no other work done. $50/pr. SALE PENDING
-LT1 "643" heads, completely stock and assembled. These are about the nicest used LT1 stock heads I've seen. Resurfaced 2k miles ago with a skim cut (.005"). Very nice cores for porting or use as-is. $175/pr.
-LT1 intake manifold, painted black (very nice job), un-ported, includes very nice CNC TPIS AIR/EGR block off plates already mounted. $70
-LT1 fuel rails w/-AN fittings welded in and billet adjustable fuel pressure regulator. SOLD
Last edited by Jason Short; 07-15-2013 at 09:07 PM.
#2
Re: LT1 aftermarket and stock (McLeod, BeCool, LT1 heads, Prothane, etc...)
Would like to buy the Bare heads. Beside the Heli coil, what other repairs or work needs to be done?
Obvious the valves & springs.
plattted@sbcglobal.net
203 269 8642
Obvious the valves & springs.
plattted@sbcglobal.net
203 269 8642
#3
Re: LT1 aftermarket and stock (McLeod, BeCool, LT1 heads, Prothane, etc...)
No other repairs needed. They came off a well running vehicle. PM me and we can figure out the payment/shipping.
Thanks!
Thanks!
#6
#9
Re: LT1 aftermarket and stock (McLeod, BeCool, LT1 heads, Prothane, etc...)
Jason, please contact me so I can send the $ for the heads. How much is the shipping to 06492? Connecticut. I can send the $ today.
Ted @ plattted@sbcglobal.net
or: 203 213 5243
Ted @ plattted@sbcglobal.net
or: 203 213 5243
#11
Re: LT1 aftermarket and stock (McLeod, BeCool, LT1 heads, Prothane, etc...)
Jason, can you shoot me a pic of the motor mounts? I think my pass. side it torn, letting my LT's hit the K-member. My email is ruqwiker2@yahoo.com
#12
Re: LT1 aftermarket and stock (McLeod, BeCool, LT1 heads, Prothane, etc...)
#15
Re: LT1 aftermarket and stock (McLeod, BeCool, LT1 heads, Prothane, etc...)
I received the bellhousing quickly and in the expected condition. Thanks Jason!!
Sent from my DROID BIONIC using Tapatalk 2
Sent from my DROID BIONIC using Tapatalk 2