CNC heads, ported intake with direct port fogger NOS
Thread Starter
Registered User
Joined: May 1999
Posts: 521
From: Reading, Pa
CNC heads, ported intake with direct port fogger NOS
Here is a whole setup ready to make power.
Pics can be seen at:
http://community.webshots.com/user/toms396
The heads are CNC'd LT1 castings with replaced valve seats for 2.02" intake / 1.60" exhaust valves. The valves are Ferrea 9000 series. They have 7/16" studs, guideplates and Comp Cams springs setup for a 250 degree / .600 lift Hydraulic roller cam. The retainers are Comp Cams Titainium. They flow the following:
.100 82 55
.200 140 104
.300 188 142
.400 238 180
.500 263 200
.600 278 210
.700 283 211
The intake is an LT1 piece ported for a 58mm tb. It has been powder coated black. It comes with an installed NOS sportsman fogger nitrous setup with 2 nitrous and 2 fuel solenoids, hard lines, distribution blocks and fogger nozzles. It also comes with an assortment of pills for a 150 and 225 hit.
I'm keeping everything else including the bottles, electronics and braided lines. This is just the installed components on the intake.
This setup made 421 rwhp and 401 ft/lbs rwtq on a 396 with a nitrous cam and 4 heat range colder plugs and a 6speed. It went 11.96 @ 116mph on the motor.
On the 225 shot it made 613 rwhp and 713ft/lbs of rwtq and the car went 10.47 @ 131mph.
This setup works and is matched well. The heads have been cleaned, inspected and re-assembled. They only have one season on them as well.
I'm asking $1700 firm shipped anywhere in the continental USA. Please PM or e-mail me at n20dave@hotmail.com
Pics can be seen at:
http://community.webshots.com/user/toms396
The heads are CNC'd LT1 castings with replaced valve seats for 2.02" intake / 1.60" exhaust valves. The valves are Ferrea 9000 series. They have 7/16" studs, guideplates and Comp Cams springs setup for a 250 degree / .600 lift Hydraulic roller cam. The retainers are Comp Cams Titainium. They flow the following:
.100 82 55
.200 140 104
.300 188 142
.400 238 180
.500 263 200
.600 278 210
.700 283 211
The intake is an LT1 piece ported for a 58mm tb. It has been powder coated black. It comes with an installed NOS sportsman fogger nitrous setup with 2 nitrous and 2 fuel solenoids, hard lines, distribution blocks and fogger nozzles. It also comes with an assortment of pills for a 150 and 225 hit.
I'm keeping everything else including the bottles, electronics and braided lines. This is just the installed components on the intake.
This setup made 421 rwhp and 401 ft/lbs rwtq on a 396 with a nitrous cam and 4 heat range colder plugs and a 6speed. It went 11.96 @ 116mph on the motor.
On the 225 shot it made 613 rwhp and 713ft/lbs of rwtq and the car went 10.47 @ 131mph.
This setup works and is matched well. The heads have been cleaned, inspected and re-assembled. They only have one season on them as well.
I'm asking $1700 firm shipped anywhere in the continental USA. Please PM or e-mail me at n20dave@hotmail.com
Last edited by N20Dave; Jan 21, 2005 at 05:40 PM.
Thread
Thread Starter
Forum
Replies
Last Post
dbusch22
Forced Induction
6
Oct 31, 2016 11:09 AM
oldschool
Parts For Sale
16
Feb 9, 2016 09:21 PM